Wood end caps on new Kronos

Discussion relating to the Korg Kronos Workstation.

Moderators: Sharp, X-Trade, Pepperpotty, karmathanever

Post Reply
User avatar
JPROBERTLA
Senior Member
Posts: 483
Joined: Mon Jul 04, 2011 2:38 pm
Location: New Orleans

Wood end caps on new Kronos

Post by JPROBERTLA »

I saw many posts complaining about the plastic end caps on the original Kronos. I have had one for almost 4 years and don't have a scratch on them.

Despite my obsessive care taking, in only 3 months my Kronos2 has managed 2 dings; one on each end cap, from people just brushing up against it on stage. I am going to order an extra set and have the originals refinished with some kind of bullet proof clear coat. Has anyone taken the K2 end caps off? Does it require the same level of disassembly required to remove the original plastic ones? Thanks
JP
_________________________________________
Kronos2-88, Behringer XR18, Turbosound IP2000 (x2), dbx DriveRack 260, KRK Rokit 8s, Mackie CFX16, Mackie SRM450(x2), Mackie SRS1500 (x2), BBE processors (x4), Roland VSR 880 (x2), Alto TS210, Alto TX10 (x3) and SoundForge
MusicLive
Full Member
Posts: 175
Joined: Fri Feb 19, 2010 9:05 pm
Location: Norfolk. England. UK
Contact:

Post by MusicLive »

Not a clue as to how the end caps come off, sorry, but the timber must be real soft if they sustain 'dings from people just brushing past'.
I dread to think what damage would occur if they were hit by a mike stand, or some similar object?

Get them sprayed in a two pack Polyester finish, then a few coats of 2 pack Acrythane Lacquer. They'll look nice too, but will withstand 'brushing' but would still suffer from any heavy impact.

Then employ a couple of German Shepard Dogs to stand guarding it! :)

Regards,

MC
User avatar
apex
Platinum Member
Posts: 2340
Joined: Tue Feb 23, 2010 6:22 am
Contact:

Post by apex »

Is it possible to put the new end caps (wooden) on the original Kronos?
Please subscribe and follow me on Youtube and Facebook for information related audio technology.

YouTube -
https://www.youtube.com/juliusdeberryjr

Facebook -
https://www.facebook.com/majesticstudiosllc

Instagram - https://www.instagram.com/majesticstudios_jld/
MusicLive
Full Member
Posts: 175
Joined: Fri Feb 19, 2010 9:05 pm
Location: Norfolk. England. UK
Contact:

Post by MusicLive »

I think the new K2 is narrower than the K1 and X so don't think they would.

Regards,

MC
jeremykeys
Platinum Member
Posts: 3093
Joined: Sun Jun 19, 2011 11:06 pm
Location: Toronto, Ontario, Canada

Post by jeremykeys »

Quite a while back, I saw a thread about some company that was making wooden end caps for the first Kronos's. I'm kind of glad I didn't bother with them. Even though mine travels in a proper road case, it has scratches and dings and certainly looks well played. I'm okay with that though. It looks a bit like me~ :wink: Well used!
If music is the food of love, play on and play loud!
Gear: Kronos 73, Wavestation EX, Polysix, King Korg, Monotron and Monotron Duo, Minikorg, Moog Grandmother, my very old MiniKorg, 4 acoustic and 9 electric guitars, 1 Ibanez 5 string bass, a Steel guitar, a bunch of microphones, 2 pairs of studio monitors and other very cool toys, 1 wife and 4 cats and a lava lamp!
Darryll
Posts: 45
Joined: Tue Sep 11, 2012 1:26 pm
Location: North Carolina

Wooden End Caps

Post by Darryll »

Does anyone know of where to order wooden end caps like the following? They look nice + practical for caring or moving the board.

https://www.youtube.com/watch?v=1cMcw5BdnaU
drdave2002
Junior Member
Posts: 96
Joined: Wed Sep 26, 2007 8:20 pm

Post by drdave2002 »

maybe I am alone here, but because I want to look after my synth I'll just be careful....... !! i do have little bits of wood, which i would like to show off in years to come..
Korg Kronos 61, M3-73, Karma (all-time classic), X5, Wavestate, Roland Juno Gi, JV, D110, Arturia Microfreak, Modal Skulpt, IK Uno. Nanopad2, M-Audio Venom, Deepmind 12D, Crave, TB3, Maschine Mk3, Moog Werkstat and a few other bits
drdave2002
Junior Member
Posts: 96
Joined: Wed Sep 26, 2007 8:20 pm

Post by drdave2002 »

i was getting excited, then realised, it's my M3 (not my Kronos) that has wood paneling edges, but to be fair, it does look good !!!
Korg Kronos 61, M3-73, Karma (all-time classic), X5, Wavestate, Roland Juno Gi, JV, D110, Arturia Microfreak, Modal Skulpt, IK Uno. Nanopad2, M-Audio Venom, Deepmind 12D, Crave, TB3, Maschine Mk3, Moog Werkstat and a few other bits
User avatar
KK
Platinum Member
Posts: 1516
Joined: Thu Oct 13, 2016 3:01 am

Post by KK »

The Kronos sides are pretty easy to remove actually - 5 or 6 screws each. Of course, you have to first remove the base wooden panel.
Bitflipper
Full Member
Posts: 121
Joined: Tue May 24, 2016 7:54 pm

Post by Bitflipper »

When I first got my K2 I vowed to be careful with the wood end caps, because with the last synth I had with wood trim (Hammond) they got scratched up pretty badly. So I bought a nice flight case with internal padding and haven't transported the Kronos once without it.

However, despite all my care the end caps are still scratched, presumably from bumping them while moving in and out of the case. As noted above, it's soft wood. Although stained to look like oak, it's not oak, which would be more scratch-resistant.

My question: has anyone tried using scratch-repair products such as this or this on their end caps?
Post Reply

Return to “Korg Kronos”