View previous topic :: View next topic |
Author |
Message |
jimknopf Platinum Member
Joined: 17 Jan 2011 Posts: 3374
|
Posted: Thu Jul 14, 2011 9:08 am Post subject: How initialize a HD-1 program? |
|
|
In fact I have two questions:
1. How do I reset a HD-1 program to "Init program" status?
2. If this program contains imported samples, is there a way to clear/delete the samples it refers to in one go, or do I have to do this separately (via sample management)? |
|
Back to top |
|
|
Broadwave Platinum Member
Joined: 25 May 2011 Posts: 1118 Location: Manchester UK
|
Posted: Thu Jul 14, 2011 9:57 am Post subject: Re: How initialize a HD-1 program? |
|
|
jimknopf wrote: | 1. How do I reset a HD-1 program to "Init program" status? |
I'm afraid there's no instant initialise function, why not copy/use an "Init program" from User bank G (unless you've changed it for EXi use, of course). Unfortunately there's no User Bank G in the factory Preload.PCG, so you can't load an "Init Program" from there either.
The first thing I did when I got mine was, to create initialised programs for each of the engines - it took a bit of time, but is worth doing
jimknopf wrote: | 2. If this program contains imported samples, is there a way to clear/delete the samples it refers to in one go, or do I have to do this separately (via sample management)? |
Are you sure you want to delete imported samples? You may be using them in another patch - just change the Oscillator multisample by selecting one from the ROM bank. _________________ Synth DIY Projects |
|
Back to top |
|
|
jimknopf Platinum Member
Joined: 17 Jan 2011 Posts: 3374
|
Posted: Thu Jul 14, 2011 10:32 am Post subject: |
|
|
Thanks for the "init info", Kronik: good idea to have an init patch in each bank then.
Yes, I want to delete imported samples in cases where I just did a test run and do not want to keep the result.
By the way, my 4Gb have just arrived.
I'm too busy the next days, but maybe next week...
Did you face any problems getting the keybed and Alu front piece back in place after unscrewing? |
|
Back to top |
|
|
Broadwave Platinum Member
Joined: 25 May 2011 Posts: 1118 Location: Manchester UK
|
Posted: Thu Jul 14, 2011 10:47 am Post subject: |
|
|
jimknopf wrote: | Did you face any problems getting the keybed and Alu front piece back in place after unscrewing? |
No, no problems at all, just take care not to cross thread the screws when you put them back in _________________ Synth DIY Projects |
|
Back to top |
|
|
theshinenz Full Member
Joined: 18 Sep 2009 Posts: 240
|
Posted: Fri Jul 22, 2011 5:13 am Post subject: |
|
|
On the same subject how do I initialize a exi program when there's no blank exi patches? |
|
Back to top |
|
|
theshinenz Full Member
Joined: 18 Sep 2009 Posts: 240
|
Posted: Fri Jul 22, 2011 8:13 am Post subject: |
|
|
Ok got this sorted now, still one other querie, I copied a program to a combo with the copy from program function, I selected the tfx, ifx, etc etc but it still sounds different, the attack etc is way different, I know this should be simple but can someone help.
Cheers
Scott |
|
Back to top |
|
|
theshinenz Full Member
Joined: 18 Sep 2009 Posts: 240
|
Posted: Fri Jul 22, 2011 11:16 am Post subject: |
|
|
Sorry guys, learning as I go, I realised the karma module had defaulted to A when it should have been B when loaded into the combi. |
|
Back to top |
|
|
|