|
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
DrHoo Platinum Member
Joined: 23 May 2010 Posts: 657 Location: North Wales, UK
|
Posted: Sun Sep 22, 2013 5:06 pm Post subject: Regarding modifying the monotron or montribe |
|
|
O.K Korg users, circuit benders & monotron/tribe users. With the introduction of the Volca series i have found that it has sparked my interest in the monotron & monotribe again. I have decided to start stocking up on pcb components so that this winter i can get modding , starting with the monotron.
I'm pretty good with a soldering iron on pcb's & make a good enough job but my technical knowledge is only that of a novice, so i want to ask a novice question !
I know that the solder on the monotron & monotribe is lead free. I have only ever soldered with lead-tin flux core before & have some good solder that i trust to use...
SO CAN I USE MY LEAD-TIN 60/40 ON THE LEAD FREE BOARD OR IS IT IMPERATIVE TO STAY WITH LEAD FREE SOLDER ? Do they mix or is it best avoided ??
Wha' d' ya say ? |
|
Back to top |
|
|
button Junior Member
Joined: 30 Aug 2013 Posts: 50 Location: Perth, Australia
|
Posted: Mon Sep 23, 2013 2:16 am Post subject: |
|
|
I have zero understanding of modding but I do know I want a version of the delay and duo together (or even all three), rehoused in a new box minus the ribbons, just the knobs with midi and extra controls. Perhaps join the pcbs/dials into a cheap basic midi keyboard.
I'd buy? that... hop to it!
Last edited by button on Wed Sep 25, 2013 6:55 am; edited 1 time in total |
|
Back to top |
|
|
Yoa Senior Member
Joined: 03 Feb 2012 Posts: 345 Location: Exeter, NH
|
Posted: Tue Sep 24, 2013 2:42 am Post subject: Re: Regarding modifying the monotron or montribe |
|
|
DrHoo wrote: | I know that the solder on the monotron & monotribe is lead free. I have only ever soldered with lead-tin flux core before & have some good solder that i trust to use...
SO CAN I USE MY LEAD-TIN 60/40 ON THE LEAD FREE BOARD OR IS IT IMPERATIVE TO STAY WITH LEAD FREE SOLDER ? Do they mix or is it best avoided ?? |
Having modded a monotron, I can say with certainty that your 60/40 will be fine. The only issue is you have to comply with the usage standards of lead-free (higher heat, longer times), which can cause bleeding (overmelting) of your 60/40. But, in general, you'll be fine. _________________ Cheers! Yoa
Current electronic equipment: Korg Kaossilator, miniKP, microKORG, nanoKEY, nanoPAD, nanoKONTROL, monotron, Pandora PX5D, AX1000G, M-Audio Keystation 88es, Casio VL Tone, Soundcraft 102 mixer, laptop (which, among other things, has the KORG Legacy Collection and various NI stuffs), Acer Iconia a100 (has many music apps), Stylophone, Yamaha DX7 |
|
Back to top |
|
|
DrHoo Platinum Member
Joined: 23 May 2010 Posts: 657 Location: North Wales, UK
|
Posted: Tue Sep 24, 2013 9:10 am Post subject: |
|
|
Thanks for that. Kinda thought it would be ok.
The marked mod points on the monotron are bare copper anyway so i don't see an issue there. I just wondered in case i have to start soldering to factory soldered areas.
I'm open to idea's too if anyone has any...Spotted this & thought it was very well done http://electro-music.com/forum/topic-57134.html
Edit. I went & got some lead free solder anyway. I'm still interested in other monotron modders though. There seems to enough of them dispersed around the web but with it being a korg product, it would make sense to have information here. It might be the first place some people look ! |
|
Back to top |
|
|
Yoa Senior Member
Joined: 03 Feb 2012 Posts: 345 Location: Exeter, NH
|
Posted: Tue Sep 24, 2013 2:26 pm Post subject: |
|
|
I modded my monotron so much that it's barely even a monotron.
I turned mine into a modular synth. The main oscillator now has 8 waveforms, 4 with CV control, as well as attenuated FM inputs. There's also a sub-oscillator with 3 waveforms, selectable -1 or -2 octaves. 2 gate inputs replace the LPG gate signal within the monotron, and is equipped with dual ASR's. The LFO has 5 waveforms and ditched the intensity control (not very useful in a modular). The VCF has CV control over both cutoff and resonance, as well as an amplified input for those gritty distorted sounds. I also added a simple 2-transistor VCA, similar to the MS-20. There's also a few utilities, like a mixer, manual voltage generators, stuff like that.
I have no pics as of yet because I'm still working on adding noise and a sample&hold circuit, and maybe seeing if I can tap the filter to get different filter types out of it, like highpass or bandpass. If you want to know how to do some of these mods, just ask. I'll post schematics n stuff. They're fairly simple mods, really.
As you can well imagine, it doesn't really run on batteries anymore. But, it does sound like a Korg... to a degree. _________________ Cheers! Yoa
Current electronic equipment: Korg Kaossilator, miniKP, microKORG, nanoKEY, nanoPAD, nanoKONTROL, monotron, Pandora PX5D, AX1000G, M-Audio Keystation 88es, Casio VL Tone, Soundcraft 102 mixer, laptop (which, among other things, has the KORG Legacy Collection and various NI stuffs), Acer Iconia a100 (has many music apps), Stylophone, Yamaha DX7 |
|
Back to top |
|
|
DrHoo Platinum Member
Joined: 23 May 2010 Posts: 657 Location: North Wales, UK
|
Posted: Tue Sep 24, 2013 2:55 pm Post subject: |
|
|
Yo !, Sounds awesome. I think that any schematics & photo's on here would be helpful.
My current plan is more simple. I'm going to build a little break out box for the pitch c.v, filter cut off c.v, & gate.
It's going to have 3x 1/4" jack sockets, a switch for switching the cut off/keyboard tracking on & off, & two pots, one for setting the pitch-in & one for the filter cut off amount.
It's based on two slightly different schematics. One from 'DIN SYNC' ( http://www.dinsync.info/2010/06/how-to-modify-korg-monotron.html ) & one from the guy at electro music.com. ( I posted a link in one of my previous posts here) The second one added a 1 meg pot to the cut off in line.
I'm going to use the 4 pin mini din connector for that little box.
I would do more but the components on the pcb are so tiny & easy to ruin. I did attempt the resonance mod on my monotron delay but i bottled out before i made a mess....Maybe some time in the future !
Also, i'm not clear on what ALL of the mod points are for exactly. I'm learning but at this stage i'm all eyes & ears. When i mod the first one i'll post some results & findings on here. |
|
Back to top |
|
|
button Junior Member
Joined: 30 Aug 2013 Posts: 50 Location: Perth, Australia
|
|
Back to top |
|
|
DrHoo Platinum Member
Joined: 23 May 2010 Posts: 657 Location: North Wales, UK
|
|
Back to top |
|
|
Yoa Senior Member
Joined: 03 Feb 2012 Posts: 345 Location: Exeter, NH
|
Posted: Sat Sep 28, 2013 4:26 pm Post subject: |
|
|
Nicely done! What made you prefer a breakout box instead of just adding controls and jacks to the unit itself? _________________ Cheers! Yoa
Current electronic equipment: Korg Kaossilator, miniKP, microKORG, nanoKEY, nanoPAD, nanoKONTROL, monotron, Pandora PX5D, AX1000G, M-Audio Keystation 88es, Casio VL Tone, Soundcraft 102 mixer, laptop (which, among other things, has the KORG Legacy Collection and various NI stuffs), Acer Iconia a100 (has many music apps), Stylophone, Yamaha DX7 |
|
Back to top |
|
|
DrHoo Platinum Member
Joined: 23 May 2010 Posts: 657 Location: North Wales, UK
|
Posted: Sat Sep 28, 2013 8:25 pm Post subject: |
|
|
Good question. Really i was being cautious & sensible. My first monotron modding. Also the size restriction, there's only 4 wires & the din socket in the unit so it's not very messy in there. The box i made up has easy access & if it needs altering i can get at it without risk of hurting the korg board. I made a few first time errors too while soldering the box & if that had been the monotron i might have damaged it. Future versions will be easier now i know the territory.
I can take the break out box to say ,a monotron delay (Which i've got) & in theory trigger that on its own (Not yet modded the delay) or to another standard monotron in the future.
That's the idea anyway & now i've been in & got a feel for it all, i might formulate a plan for something more elaborate.
I'd really like to make up a new box & put it all in that for tidiness & space saving so maybe next time eh ! _________________ My current Korg gear. MS20 Mini... & now the .... Oh, maybe not !
...Had a few other Korg things over the years. |
|
Back to top |
|
|
button Junior Member
Joined: 30 Aug 2013 Posts: 50 Location: Perth, Australia
|
Posted: Sun Sep 29, 2013 3:20 am Post subject: |
|
|
i still don't understand this breakout box, what is this triggering you speak of? do you control it from a midi keyboard plugged into the breakout box? how are you using it in a musical sense? |
|
Back to top |
|
|
DrHoo Platinum Member
Joined: 23 May 2010 Posts: 657 Location: North Wales, UK
|
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|