|
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
ILM4axe
Joined: 08 Sep 2014 Posts: 3
|
Posted: Mon Sep 08, 2014 12:25 pm Post subject: Midi commands to X50 from Ext midi controller |
|
|
Hi,
I'm new to Midi controllers and I'm trying to understand how to issue a bank/combi/patch # change command from an external midi controller. Basically, I'm using a midi foot controller to simultaneously select my guitar, keyboard, and Roland drum sampler patches. I'm trying to, that is! Does it take multiple commands to change mode/bank/patch on the X50?
I understand that I must assign each device its own midi channel, and I understand that the guitar and drum patches basically use patches 0-999. But how do I tell the Korg X50 to change to....Combi Bank C Patch 109, for example?
Any advice would be appreciated....I'm obviously WAY behind the curve here.
Thanks,
Jim |
|
Back to top |
|
|
ILM4axe
Joined: 08 Sep 2014 Posts: 3
|
Posted: Thu Sep 11, 2014 9:42 pm Post subject: |
|
|
Anyone? For example, what would the proper # be for Comi C109? |
|
Back to top |
|
|
jcg
Joined: 12 Aug 2014 Posts: 21
|
Posted: Sat Sep 20, 2014 3:41 pm Post subject: |
|
|
Hi,
You need to send a maximum of 4 MIDI messages to change Combi/Prog. Here's how it works. Please note: all numbers are in Hexadecimal format! (use windows Calculator or http://www.binaryhexconverter.com/hex-to-decimal-converter if you need it in Decimal format).
1. Select Mode (System Exclusive Message)
F0 42 30 7A 4E 0m F7
m:
0 = Combi mode
2 = Program mode
4 = Multi mode
2. Select Bank (two MIDI messages; not used in Multi mode)
Bn 00 mm
Bn 20 bb
n: MIDI Channel (0 = MIDI channnel 1)
mm: Bank mode:
00 = User banks, when Bank Map in Global Mode is "KORG"
3F = User banks, when Bank Map in Global Mode is "GM"
79 = G
78 = g(d)
bb: Bank number: User banks: 0-4 (Combi: 0-2; Program: 0-3 on X50, 0-4 on MicroX)
GM Banks: 0 (always)
3. Select Program/Combi (not used in Multi mode)
Cn pp
n: MIDI channel
pp: Program/Combi number (00-7F)
4. Select multi (only in Multi mode)
F3 ss
ss: Multi number (song) (00-7F)
So, in your example, you should send the following MIDI messages (assuming MIDI channel 1 and that you have "Bank Map" in Global Mode set to "GM", which I think is the default):
F0 42 30 7A 4E 00 F7
B0 00 3F
B0 20 02
C0 6D
Each 2 digits is a number (byte, in Hexadecimal format) you must send via MIDI.
Note: if you don't need to change Mode, you don't have to send the first message. In the same way, if you also don't need to change Bank, then you can send the last message only (Program change). But it does not hurt to send them all (so it will always work, no matter where you are).
Regards,
jcg. |
|
Back to top |
|
|
nicolasdbaez
Joined: 25 May 2016 Posts: 1
|
Posted: Wed May 25, 2016 5:30 am Post subject: korg x50 y roland ax1 |
|
|
Hello greetings
I'm new in this forum.
I just bought a Roland AX1, and would need to know how to "send" these midi messages on this keyboard.
I read a lot and I can not find the way.
I hope please help me ...
Regards!!!!! |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|