View previous topic :: View next topic |
Author |
Message |
plutonia
Joined: 10 Feb 2017 Posts: 12
|
Posted: Thu Feb 16, 2017 1:41 pm Post subject: monologue triangle shape crackling sound. please fix korg! |
|
|
when using 'shape' the triangle wave produces unpleasant crackling sound. it does it when moving intensity knob in LFO section when LFO is affecting the wave 'shape'. it shouldn't do this. can it be fixed korg? |
|
Back to top |
|
|
MeneerJansen Junior Member
Joined: 13 Dec 2016 Posts: 65
|
Posted: Thu Feb 16, 2017 3:19 pm Post subject: |
|
|
I don't have this problem. What are your settings exactly? |
|
Back to top |
|
|
plutonia
Joined: 10 Feb 2017 Posts: 12
|
Posted: Thu Feb 16, 2017 4:02 pm Post subject: |
|
|
triangle wave in either osc with 'shape' all way to left. filter cut off fully open. lfo in 'shape' mode, lfo on 'slow' and rate slow is where it's most noticeable. move 'int' knob in lfo and when it gets past halfway it produces crackling sound as knob is moved.
odd and unmusical behavior! |
|
Back to top |
|
|
MeneerJansen Junior Member
Joined: 13 Dec 2016 Posts: 65
|
Posted: Thu Feb 16, 2017 7:53 pm Post subject: |
|
|
plutonia wrote: | triangle wave in either osc with 'shape' all way to left. filter cut off fully open. lfo in 'shape' mode, lfo on 'slow' and rate slow is where it's most noticeable. move 'int' knob in lfo and when it gets past halfway it produces crackling sound as knob is moved.
odd and unmusical behavior! |
You might be right but I can barely hear it. But I use a Bass speaker. That one might not play back high cackling very good. Luckily the crackling does not occur during the oscillation itself if you keep a note pressed. |
|
Back to top |
|
|
plutonia
Joined: 10 Feb 2017 Posts: 12
|
Posted: Thu Feb 16, 2017 8:31 pm Post subject: |
|
|
just read sound on sound review just now, and mentions the triangle wave folding and crackling:
"all waves (except noise) are
modified using the Shape knob. So as well
as regular pulse width adjustment, you’re
treated to a (slightly crackly) wavefolding
of the triangle waveform"
so assume it's not a fault in mine. pretty sure an analogue synth shouldn't behave like this. hope a firmware update fixes it. getting loads of great sounds from it tho! |
|
Back to top |
|
|
John01W Platinum Member
Joined: 13 Dec 2002 Posts: 1301 Location: Tejas
|
Posted: Fri Feb 17, 2017 3:29 am Post subject: |
|
|
MeneerJansen wrote: | I don't have this problem. What are your settings exactly? |
Me either. |
|
Back to top |
|
|
moho
Joined: 24 Feb 2016 Posts: 34
|
Posted: Fri Feb 17, 2017 5:08 am Post subject: |
|
|
I can confirm there is a slight crackle,
weirder is the action of the saw lfo on the shape,
when applied to the square it acts as you expect steadily changing the shape then dropping back to the start.
when applied to the saw it acts like a triangle only acting like a saw when you turn the oscillators shape up and only acting like you expect when the oscillators shape is turned up fully, weird but workable.
when applied to the triangle no matter what settings are used it acts like a triangle, steady rise steady fall.
Can anyone confirm this ? |
|
Back to top |
|
|
John01W Platinum Member
Joined: 13 Dec 2002 Posts: 1301 Location: Tejas
|
Posted: Fri Feb 17, 2017 6:34 am Post subject: |
|
|
moho wrote: | I can confirm there is a slight crackle,
weirder is the action of the saw lfo on the shape,
when applied to the square it acts as you expect steadily changing the shape then dropping back to the start.
when applied to the saw it acts like a triangle only acting like a saw when you turn the oscillators shape up and only acting like you expect when the oscillators shape is turned up fully, weird but workable.
when applied to the triangle no matter what settings are used it acts like a triangle, steady rise steady fall.
Can anyone confirm this ? |
The selected waveform of the lfo is distinctly different for me on all 3 settings on triangle waves when modulating the shape. |
|
Back to top |
|
|
moho
Joined: 24 Feb 2016 Posts: 34
|
Posted: Fri Feb 17, 2017 11:20 am Post subject: |
|
|
John01W wrote: | moho wrote: | I can confirm there is a slight crackle,
weirder is the action of the saw lfo on the shape,
when applied to the square it acts as you expect steadily changing the shape then dropping back to the start.
when applied to the saw it acts like a triangle only acting like a saw when you turn the oscillators shape up and only acting like you expect when the oscillators shape is turned up fully, weird but workable.
when applied to the triangle no matter what settings are used it acts like a triangle, steady rise steady fall.
Can anyone confirm this ? |
The selected waveform of the lfo is distinctly different for me on all 3 settings on triangle waves when modulating the shape. |
Different is not the same as correct,
Try these settings
Initialize patch,
select triangle as oscillator 1 wave with shape at 0
select saw as lfo wave with a slow rate so you can see and hear the change
set intensity to max and target shape.
Now does the wave shape jump to fully wave shaped then slowly return to not (or vice versa) as you would expect from a saw
or as mine does smoothly change then smoothly change back like a half speed triangle? |
|
Back to top |
|
|
|