|
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
ando727 Full Member
Joined: 07 Mar 2016 Posts: 102
|
Posted: Sun Dec 03, 2017 3:28 am Post subject: Using LFOs |
|
|
Ok, so I'm gradually figuring out how to design sounds on this thing - it's terribly complex compared to what I'm used to on older synths, but I'm getting there. My biggest confusion is in using the LFOs. I'm getting nowhere in understanding the signal paths, how to get them to behave in obvious ways. Even finding parameters that actually predictably do anything is a challenge at the moment. I'm using the HD1 engine - LFOs were incredibly simple on my old Korg T1, but I suspect the possibilities are so endless on the Kronos that I am not seeing the basic functionality in them.
Are there any detailed tutorials on using the LFOs anywhere? I haven't been able to find them as yet. I want to really understand the architecture of them and know how to get the sounds I imagine in my head. I'd like to know how to use them generally in sounds, but also how to assign them to joystick control and vary them that way.
Thankyou. _________________ Kronos 2 88, Korg T1, Mesa Boogie Triaxis/2:90, TC G-major II. |
|
Back to top |
|
|
19naia Platinum Member
Joined: 29 Nov 2012 Posts: 1216
|
Posted: Sun Dec 03, 2017 6:07 am Post subject: |
|
|
Page 91 parameter guide. Start there.
LFO is an AMS source to be assigned to parameters. I bet one LFO can be assigned as AMS over a parameter of another LFO.
If not careful you could tune up frequencies that will levitate the speakers like UFOs or poltergeist depending on who sees it happen.
ß
Not worth explaining because you are right about the complexity. But it is a bit simple on the setup page unless you have a preconceived shape in mind without the actual image of the waveform itself. The guide tells you which parameter sets or tweaks the waveform shape.
Page 75 covers using LFO over filters. LFO has to be assigned as AMS to a parameter first before you can hear what it is doing. If you know what parameter you want and what LFO wave form, then the rest is easy. No one can know what you want unless it is an excerpt from a preset program somewhere or from another keyboard.
Good luck. |
|
Back to top |
|
|
19naia Platinum Member
Joined: 29 Nov 2012 Posts: 1216
|
Posted: Sun Dec 03, 2017 6:17 am Post subject: |
|
|
LfO pages have parameters for the LFO and that is where you will find AMS options from which you can select JS x&y to modulate for you, if available on the AMS list.
2 LFO per OSC and then a Common LFO. So you have to know which LFO you are setting up and be sure it is the right one being used. Or maybe Kronos simplfied the AMS list LFO options, to make it harder to confuse the wrong one. ?
Again, good luck. |
|
Back to top |
|
|
Liviou2004 Platinum Member
Joined: 20 Feb 2017 Posts: 1150 Location: France
|
Posted: Sun Dec 03, 2017 11:52 am Post subject: Re: Using LFOs |
|
|
ando727 wrote: | Ok, so I'm gradually figuring out how to design sounds on this thing - it's terribly complex compared to what I'm used to on older synths, but I'm getting there. My biggest confusion is in using the LFOs. I'm getting nowhere in understanding the signal paths, how to get them to behave in obvious ways. Even finding parameters that actually predictably do anything is a challenge at the moment. I'm using the HD1 engine - LFOs were incredibly simple on my old Korg T1, but I suspect the possibilities are so endless on the Kronos that I am not seeing the basic functionality in them.
Are there any detailed tutorials on using the LFOs anywhere? I haven't been able to find them as yet. I want to really understand the architecture of them and know how to get the sounds I imagine in my head. I'd like to know how to use them generally in sounds, but also how to assign them to joystick control and vary them that way.
Thankyou. |
In order not to be completely overwhelmed in the Kronos, you should follow the user's guide page by page, step by step.
Then, I agree with what has been already said : go to Parameter's Guide.
What is important to know, is the AMS system wich is very close to the real modular system :
- on one hand, you have numbers of modulation sources, including LFOs, enveloppes, etc.
- On the other hand you have numbers of parameters that can be modulated by AMS sources.
On a basic work, there is no connection between the both. So, if you want to modulate one thing (filter cutoff for instance) you have to connect one modulation source (LFO1 for instance) to the cutoff frequency. If you don't do that, you won't get any modulation. Things are going exactly the same way on a modular analog system, except here you don't plug physical wire but just modify a parameter on the screen.
So the procedure is
1) identify where is the parameter you want to bee modulated
2) set it to the right source (here, LFO1 for example)
3) set the intensity of modulation, on the same page
4) go to the modulator page. Here, the LFO1 page
5) set the parameter you want for this modulator. For instance, choose le LFO waveform.
If you use somme method, you won't be drowned. |
|
Back to top |
|
|
ando727 Full Member
Joined: 07 Mar 2016 Posts: 102
|
Posted: Sun Dec 03, 2017 9:34 pm Post subject: |
|
|
Thankyou for your replies guys, I'll give it another try tonight and let you know how I get on.
It's amazing how much time I have spent on my Kronos trying to get it to sound like my old T1 patches! _________________ Kronos 2 88, Korg T1, Mesa Boogie Triaxis/2:90, TC G-major II. |
|
Back to top |
|
|
Liviou2004 Platinum Member
Joined: 20 Feb 2017 Posts: 1150 Location: France
|
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|