View previous topic :: View next topic |
Author |
Message |
Flabis66
Joined: 13 Oct 2018 Posts: 46 Location: Singapore
|
Posted: Tue Oct 16, 2018 12:56 pm Post subject: K&M 18810 stand with Kronos 2 |
|
|
Quick question. I just received my Kronos and a K&M stand 18810
I'm mounting the stand. In which legs holes do i have to fix the support so the keys are at the same heigh than an acoustic piano? I don't want to install everything and then realise that it's too heigh or too low.
thx |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3777
|
Posted: Tue Oct 16, 2018 1:13 pm Post subject: |
|
|
Standard piano key height is probably around 725mm (28" to 29") above ground. Hopefully your Kronos is now out of the box :-) If so, measure the distance from the tops of the keys to the base of the Kronos. Subtract that from 725mm, and set the height of the stand's base supports above the floor to this figure.
There again, there is no such thing as a standard piano player. The height of the stool will probably be just as important, but that should be set to best suit the individual and their playing style. For rock 'n roll, standing up may be quite agreeable.
"Fine" adjustments can be made once the Kronos is in place, made easier if there is someone to support its weight whilst the stand height is adjusted. |
|
Back to top |
|
|
Flabis66
Joined: 13 Oct 2018 Posts: 46 Location: Singapore
|
Posted: Tue Oct 16, 2018 1:33 pm Post subject: |
|
|
The Kronos is still in the box, too heavy for me to unbox it alone and bring it to the first floor (I think, but i can try), my husband is coming back in 1 hour to help me. So i can't measure it now.
But if you say that we can easily change the heigh after, i can continue to assemble the stand and accessories. Thank you. |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3777
|
Posted: Tue Oct 16, 2018 3:06 pm Post subject: |
|
|
The instructions supplied with the K&M 18810 stand argue against adjusting the stand whilst it is loaded, but it is possible, provided all the weight is taken off the stand foot that is being adjusted, and allowing it to move up and down without any weight on it, hence the need for a helper. Just make sure the locking knob is in place and screwed in before lowering that end of the stand, then repeat for the other end. |
|
Back to top |
|
|
Flabis66
Joined: 13 Oct 2018 Posts: 46 Location: Singapore
|
Posted: Thu Oct 18, 2018 9:43 pm Post subject: |
|
|
In case of someone else search this info,
I put the screw randomly in the third hole (from bottom) and hopefully it's at the perfect height |
|
Back to top |
|
|
DeltaJockey Senior Member
Joined: 27 Jul 2015 Posts: 303 Location: East Gippsland, Australia
|
Posted: Fri Oct 19, 2018 5:51 am Post subject: |
|
|
I have mine right at the bottom, as I like the keyboard to be a bit lower than standard. I like that the Kronos RH3 is one of the few weighted boards with a very shallow keybed height from the bottom of the case. Most other boards I find are much "thicker" vertically and I often can't get even standard piano height with the stands on minimum.
I think 3 holes up may be too high. Yes, if you're careful you can lower it with the Kronos on top, but only do one hole level at a time alternating sides. |
|
Back to top |
|
|
|