View previous topic :: View next topic |
Author |
Message |
Paul999
Joined: 09 Nov 2018 Posts: 5 Location: UK
|
Posted: Fri Nov 09, 2018 10:10 am Post subject: Control Karma Scenes via midi |
|
|
Hi I want to turn karma scenes on and off from my nanopad2. I can see under global i can set scene change by entering cc30 under midi cc assign. So I can turn scene 1 on by sending cc30. I cant see where i enable the kronos to receive CC31, cc32, cc33 etc for scenes 2,3,4 etc. I have tried just sending cc31 from the nanopdad but kronus does not respond. Can someone advise what i have missed. Thankyou. |
|
Back to top |
|
|
CharlesFerraro Platinum Member
Joined: 06 Feb 2010 Posts: 955 Location: California
|
Posted: Fri Nov 09, 2018 10:57 pm Post subject: |
|
|
Hi Paul, welcome to Korgforums.
The value of CC30 chooses the KARMA scene.
A value of 0 will choose scene 1, a value of 1 will choose scene 2, a value of 2 will choose scene 3 etc. All the way up to a value of 7 for scene 8. It's easy to remember that MIDI starts counting at zero.
CC31 turns KARMA's latch function on and off. CC31 values 0-63 turn latch off while values 64-127 turn latch on. _________________ paypal.me/CharlesFerraro |
|
Back to top |
|
|
Paul999
Joined: 09 Nov 2018 Posts: 5 Location: UK
|
Posted: Fri Nov 09, 2018 11:43 pm Post subject: |
|
|
Hi thank you for your response. So what is the exact format to select say karma scene 2 from say the nanopad 2. Sorry if this is a basic question. Thanks |
|
Back to top |
|
|
CharlesFerraro Platinum Member
Joined: 06 Feb 2010 Posts: 955 Location: California
|
Posted: Sat Nov 10, 2018 1:04 am Post subject: |
|
|
I don't use a nanopad2 so I'm not sure. I could read the manual for you but... ehhh you know. Not gonna take the time to do that rn. Would be a really easy question to answer though. You were able to program a pad to send CC30, so can you program a pad to send CC30 with a value of 0 or 7? Does it send a value depending on how hard you hit the pad (velocity)? Is there a fixed velocity mode per pad? Maybe pads only act as switches so a pad sends a CC value of 127 when triggered and rests at value 0. I really don't know, but your answer is only a few page turns away. If you can't figure it out after ten minutes of reading then maybe I'll take a look at the nanopad2 manual to see what's up. _________________ paypal.me/CharlesFerraro |
|
Back to top |
|
|
mikelees Junior Member
Joined: 21 Mar 2012 Posts: 94 Location: Chelmsford, UK
|
Posted: Sat Nov 10, 2018 7:33 am Post subject: |
|
|
Hi,
On the nanoPad2, the top 8 pads are always mapped to the 8 Kronos chord pads. Kronos ignores the nanoPad settings for the top 8 pads, except toggle.
If you set up pads to send CC30 values, then it will need to be one of the lower 8 pads. |
|
Back to top |
|
|
robertaramar
Joined: 23 Oct 2017 Posts: 9
|
Posted: Sat Nov 10, 2018 10:38 am Post subject: Are you sure on CC30? |
|
|
Hi,
I just checked switching KARMA scenes on my Kronos and it does NOT work with CC30 but it DOES work with CC85.
Also, wenn I monitor the MIDI commands that the KRONOS issues when switching KARMA scenes with its buttons, it will issue CC85.
Regards,
Robert |
|
Back to top |
|
|
Paul999
Joined: 09 Nov 2018 Posts: 5 Location: UK
|
Posted: Sat Nov 10, 2018 7:37 pm Post subject: |
|
|
Hi, i think maybe this is a nanopad constraint. I cant see where the nanopad will allow the additional parameters to be added to the cc30 to select required scene. I can assign just cc1 to 127 per pad. Unless i am missing something. No big deal as i can use buttons on the kronos, just pads would have been easier to hit gigging. |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3777
|
Posted: Sat Nov 10, 2018 8:54 pm Post subject: |
|
|
The X-Y pad on the nanoPAD2 sends CC# messages having parameter values that change with the finger position on the pad, but the individual pads themselves only send fixed CC#. |
|
Back to top |
|
|
Paul999
Joined: 09 Nov 2018 Posts: 5 Location: UK
|
Posted: Sat Nov 10, 2018 9:08 pm Post subject: |
|
|
Hi yes, thanks i can see that now. So a different pad or will stick with kronos keys. Thanks for comments. |
|
Back to top |
|
|
GregC Platinum Member
Joined: 15 May 2002 Posts: 9451 Location: Discovery Bay (San Francisco Bay Area)
|
Posted: Sat Nov 10, 2018 9:33 pm Post subject: |
|
|
Paul999 wrote: | Hi, i think maybe this is a nanopad constraint. I cant see where the nanopad will allow the additional parameters to be added to the cc30 to select required scene. I can assign just cc1 to 127 per pad. Unless i am missing something. No big deal as i can use buttons on the kronos, just pads would have been easier to hit gigging. |
I use a foot switch _________________ Kronos 88. MODX8
Achieve your musical dreams
https://soundcloud.com/user-898236994 |
|
Back to top |
|
|
Paul999
Joined: 09 Nov 2018 Posts: 5 Location: UK
|
Posted: Sun Nov 11, 2018 8:04 am Post subject: |
|
|
Thanks. May be the way to go. Which foot switch do you use? |
|
Back to top |
|
|
GregC Platinum Member
Joined: 15 May 2002 Posts: 9451 Location: Discovery Bay (San Francisco Bay Area)
|
|
Back to top |
|
|
|