|
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
DeltaJockey Senior Member
Joined: 27 Jul 2015 Posts: 303 Location: East Gippsland, Australia
|
Posted: Wed May 15, 2019 5:05 am Post subject: Cardboard spacers - New Kronos 2 vs older Kronos models |
|
|
So,
as I have always understood, Korg ceased supplying the cardboard spacers when the Kronos 2 was released back in 2015.
I've owned both vintage, and I'm wondering whether the metal "key slip" panel, (I'm a pianist) , is actually any stronger on the Kronos 2 88 than the earlier models.
I still ponder this, as I am still using my own cardboard wedged across the middle when carrying the board just in relocating locally. Because when I pick it up and the centre area rests against my stomach, there is still some give pushing toward the keybed, and to me, it feels about the same as the Kronos X 88 I used to own. There is a slight inward bend if I don't use the spacers.
I'd love to know whether Korg officially state that the metal keyslip panel is actually stronger than previous models or they've just reviewed there policy and just to be safe we should transport it with them anyway,
I'm eager for anyone else view on this..... _________________ The companions I can't live without: Kawai Acoustic Grand, Kawai MP11SE, Yamaha Montage8, Korg D1
Other important stuff: Kronos2-73, Studiologic NC2X, NI Komplete Ultimate 11, Sonuscore Elysion and Orchestra, Pianoteq, Experimenta Due. |
|
Back to top |
|
|
GregC Platinum Member
Joined: 15 May 2002 Posts: 9451 Location: Discovery Bay (San Francisco Bay Area)
|
Posted: Wed May 15, 2019 2:54 pm Post subject: |
|
|
I doubt Korg explained this. And after some yrs, not expecting anything.
I suppose some think the cardboard shivs are fussy. I think they are a simple precaution, a way to keep the heavy key bed mechanism from shifting around.
I have the 2011 Kronos 88 so I can't do a "A vs B ' comparison of how the heavy RH3 is attached to the frame/chassis.
Anyway, I respect the physics- Rh3 is heavy. Mounting screws [or whatever fastener] are bound to get a little loose. If so, the RH3 will shift potentially.
If RH3 88 shifts too much, noisey keys, clacking , possibly stuck keys result.
This is my opinion.
Of course, Korg 'should' never create this potential. Then again, I have a long list of " Korg shoulds". _________________ Kronos 88. MODX8
Achieve your musical dreams
https://soundcloud.com/user-898236994 |
|
Back to top |
|
|
BobTheDog Platinum Member
Joined: 21 May 2007 Posts: 1535
|
Posted: Wed May 15, 2019 6:47 pm Post subject: |
|
|
If I move mine I pad out the space, it doesn't take long to do. |
|
Back to top |
|
|
KK Platinum Member
Joined: 13 Oct 2016 Posts: 1422
|
Posted: Wed May 15, 2019 7:17 pm Post subject: |
|
|
If they were really made of cardboard, it would be very easy for you to make new ones. Cardboard resistance/strength is quite limited, so I doubt it helps much to prevent the metal "front bumper" to bend if there is a force pushing in its center.
There is a very simple procedure to replace the RH3 assembly back to its correct position. Place the Kronos on pillows holding it with one hand on its rear panel, then use other hand to loosen the action screws (bigger ones under the unit) a few turns and then screw them back tightly. Gravity will make sure it is correctly placed. |
|
Back to top |
|
|
DeltaJockey Senior Member
Joined: 27 Jul 2015 Posts: 303 Location: East Gippsland, Australia
|
Posted: Wed May 15, 2019 11:52 pm Post subject: |
|
|
thanks to all of you for your input!
I have to confess I am also guilty of not properly reading a post before making a reply
I already did have the same thoughts as all of you. I did state in my post that I already use my own cardboard spacers on my Kronos 2. They work very well. I don't have any issues with keybed movement, and I keep the screws well tightened in any case. It's more about preventing the bowing in of the key slip bar, as even on the Kronos 2 I noticed without the spacers, the bar with pressure would start to curve in eventually. Being the perfectionist I am, I wish to keep my Kronos in as new condition as possible.
It's just my question about whether there being no supplied spacers with current models meant the key slip bar was stronger and not needing them, or Korg just stopped bothering to supplying them.
I'll take that as an "I don't know". I suppose I could just contact Korg support to see if they can get an answer from Japan for me. But it's just a petty thought bubble, which I wondered if anyone else had pondered.
I know it's just a "first world problem" , ....so excuse me, and I'll go back to actually playing my Kronos _________________ The companions I can't live without: Kawai Acoustic Grand, Kawai MP11SE, Yamaha Montage8, Korg D1
Other important stuff: Kronos2-73, Studiologic NC2X, NI Komplete Ultimate 11, Sonuscore Elysion and Orchestra, Pianoteq, Experimenta Due. |
|
Back to top |
|
|
DeltaJockey Senior Member
Joined: 27 Jul 2015 Posts: 303 Location: East Gippsland, Australia
|
Posted: Thu May 16, 2019 12:19 am Post subject: |
|
|
GregC wrote: | I doubt Korg explained this. And after some yrs, not expecting anything.
Of course, Korg 'should' never create this potential. Then again, I have a long list of " Korg shoulds". |
thanks Greg, my sentiments exactly _________________ The companions I can't live without: Kawai Acoustic Grand, Kawai MP11SE, Yamaha Montage8, Korg D1
Other important stuff: Kronos2-73, Studiologic NC2X, NI Komplete Ultimate 11, Sonuscore Elysion and Orchestra, Pianoteq, Experimenta Due. |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|