|
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
loopman Junior Member
Joined: 13 Jun 2012 Posts: 71
|
Posted: Tue Aug 23, 2016 2:51 pm Post subject: Filter |
|
|
Hello,
there would be a way to achieve an FM Filter on my Radias?
Thanks a lot |
|
Back to top |
|
|
OpAmp Platinum Member
Joined: 07 Jun 2013 Posts: 1176 Location: Brussels, BE
|
Posted: Tue Aug 23, 2016 10:20 pm Post subject: |
|
|
Hi,
What exacty do you understand under FM Filter?
Virtual patches will help you most likely. Route one to the cutoff of the filter and use as source of the patch an LFO, or keytracking, depending on what you understand FM.
Good luck. _________________ microKORGXL, Kaossilator Pro, monotribe, SQ-1, volca fm, Kross 88 BK
Alesis SR18, Akai Miniak, Fender Strat, Line 6 Spider II 112, Zoom MS-50G |
|
Back to top |
|
|
Citizen Klaus Full Member
Joined: 23 Jul 2009 Posts: 171 Location: Bloomington, IN
|
Posted: Tue Aug 23, 2016 11:37 pm Post subject: |
|
|
If you mean audio-rate FM of the filter, the RADIAS doesn't really do that. The best you can get is a fast LFO.
That said, the sorts of timbres you can create by audio-rate filter FM can easily be achieved through other means on the RADIAS. Do you want to fuzz up your sound a bit, like you'd get with subtle audio-rate FM at lower resonance settings? Use some pre-filter drive. Do you want to do audio-rate FM of a sine oscillator, like you'd get with a filter at high resonance settings? Use the Cross or VPM options for Osc Mod with Osc 1 set to a sine. |
|
Back to top |
|
|
loopman Junior Member
Joined: 13 Jun 2012 Posts: 71
|
|
Back to top |
|
|
OpAmp Platinum Member
Joined: 07 Jun 2013 Posts: 1176 Location: Brussels, BE
|
Posted: Wed Aug 24, 2016 9:54 pm Post subject: |
|
|
Hi,
I've not seen any filter with FM modulation to be honest...
The first video describes what I mentioned in a previous post. In fact I would call it cutoff modulation, meaning the cutoff frequency is modulated by another oscillator. In the particular video, it is done by an LFO (low frequency oscillator). As said before use a virtual patch on the radias to route the LFO (source) to the cutoff frequency of the filter (destination). Don't forget to turn up the modulation intensity of the virtual patch. Further on, play with the initial setting of the cutoff frequency and the parameters of the chosen LFO for modulation. Possibly you want to set up a second virtual patch to modulate the resonance of the filter as well.
By the way, the example in the first video is not that interesting in my opinion. The initial oscillator is a sine wave send through a modulated filter. As the spectrum of a sine wave is only one spectral line, the modulation is in fact more or less the same as modulating the amplitude of the sine wave. More interesting results can be achieved by starting with a waveform with more harmonics like saw or square. The cutoff modulation will change the harmonic content and thus the waveform continously.
Have fun! _________________ microKORGXL, Kaossilator Pro, monotribe, SQ-1, volca fm, Kross 88 BK
Alesis SR18, Akai Miniak, Fender Strat, Line 6 Spider II 112, Zoom MS-50G |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|