|
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
pasblas
Joined: 06 Feb 2017 Posts: 5
|
Posted: Sat Mar 04, 2017 6:12 pm Post subject: Problem with select category |
|
|
Hello, sorry for my english translator. I have a Korg trinity plus, when I enter select category and I put a sound suddenly change me to another sound only without touching anything, also when I am in edit the parameters change alone from time to time . Has anyone had this happen? Do you know what the cause might be and if there is any provision for this?
If I reboot with enter + 0 I would continue with OS version 2.4.1? Or I would have to install it again, thanks |
|
Back to top |
|
|
pasblas
Joined: 06 Feb 2017 Posts: 5
|
Posted: Thu Mar 16, 2017 5:55 am Post subject: |
|
|
When I edit some sound and change a parameter and at the same time I play a key sometimes it changes only the parameter. I also noticed that with the slider value to 0 nothing happens in category selection, but if I play when I am editing if it is They move the parameters. Really nobody has this happened? Thanks |
|
Back to top |
|
|
pasblas
Joined: 06 Feb 2017 Posts: 5
|
Posted: Tue Mar 21, 2017 10:49 am Post subject: |
|
|
I must be the only one who happens to this xD |
|
Back to top |
|
|
nitecrawler Platinum Member
Joined: 22 Mar 2007 Posts: 974 Location: from a mile high to the the AZ desert
|
Posted: Tue Mar 21, 2017 1:04 pm Post subject: |
|
|
As to your first concern, my quick answer is "no" that does not happen on my Trinity. My initial thought was that you may have a faulty touch screen, but that is a guess only. As to your other questions, I have no opinion. Maybe some others here will chime in. _________________ http://www.soundclick.com/bands/default.cfm?bandID=807494
Montage M7, Pa5x76, Nautilus, PA3Xle, Oasys 76, Mini-Moog, EMU Audity 2000, Motion Sound KBR 3D amp, Presonus and Reaper DAW W/Tannoy Reveal 501A powered monitors |
|
Back to top |
|
|
Timo Platinum Member
Joined: 24 Jan 2002 Posts: 3109 Location: Kaoss central, England
|
Posted: Tue Mar 21, 2017 7:18 pm Post subject: |
|
|
pasblas wrote: | I must be the only one who happens to this xD |
I've not experienced your problem.
Is the Trinity connected by MIDI to anything else? I wonder if an external controller could be doing it.
If you wish to reset the Trinity, save all your PCG data first, then hold Enter + 0 as you power on the Trinity and it will carry out a system reset. No, you wont have to re-install OS v.2.41 afterwards, but you will have to reload your PCG data again to restore your patches. _________________ [Free Moss Set For All Workstations With Moss Expansion]
[Infekted.org - Original Access Virus Forum & Community]
Trinity V3 PBS | Radias KB | Virus TI Snow | Virus Indigo 1 | 505 Groovebox |
|
Back to top |
|
|
pasblas
Joined: 06 Feb 2017 Posts: 5
|
Posted: Fri Mar 24, 2017 2:59 pm Post subject: |
|
|
It is not connected to anything MIDI, I have already restored it and nothing continues to do it when I want, even in the slider of the screen, I put it to +10 and down to only -10 especially when I play, if I do not play, nothing happens.
I already had to disconnect the Ribbon because it did not let me change parameters in combi mode, and I had to disconnect it. |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|