Korg Forums Forum Index Korg Forums
A forum for Korg product users and musicians around the world.
Moderated Independently.
Owned by Irish Acts Recording Studio & hosted by KORG USA
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

R3 Pitch Wheel Assignment

 
Post new topic   Reply to topic    Korg Forums Forum Index -> Korg RADIAS / R3
View previous topic :: View next topic  
Author Message
DiscoDean



Joined: 25 Nov 2020
Posts: 5

PostPosted: Wed Nov 25, 2020 3:02 pm    Post subject: R3 Pitch Wheel Assignment Reply with quote

Hi, hoping someone can help me out...

I'm trying to set up a split keyboard with midi. Everything works good except that I want to disable the pitch wheel on the timbre going to the low end. I've gone through the patch settings and can't figure it out. The midi is being used with a drum machine that's controlling the low end timbre, but when I'm using the pitch wheel for the high end timbre it's bending the low end as well which i don't want. Make sense??
Back to top
View user's profile Send private message
Nealster



Joined: 19 Jan 2008
Posts: 38
Location: Sweden

PostPosted: Thu Nov 26, 2020 1:18 pm    Post subject: Reply with quote

Hi DiscoDean!

Edited:
I first replied with how to do this on the Radias, then I realized you were asking about the R3.

I don't have an R3, but according to the manual on page 26, the R3 should have the Bend Range setting under "PITCH-B".
Change this setting to 0 for your lower timbre:



Hope this helps!
_________________
M3 | Kronos | Radias | Wavestation | Cubase 9.5
Back to top
View user's profile Send private message
DiscoDean



Joined: 25 Nov 2020
Posts: 5

PostPosted: Thu Nov 26, 2020 6:51 pm    Post subject: Reply with quote

Brilliant, thank you I'll try it!
Back to top
View user's profile Send private message
DiscoDean



Joined: 25 Nov 2020
Posts: 5

PostPosted: Fri Nov 27, 2020 7:08 pm    Post subject: Reply with quote

This didn't do what I was hoping...

I only want the pitch wheel to affect the upper end of the split keyboard and not the bottom. This adjusts the whole keyboard on both timbres.

Maybe what I want to do isn't possible?
Back to top
View user's profile Send private message
OpAmp
Platinum Member


Joined: 07 Jun 2013
Posts: 1173
Location: Brussels, BE

PostPosted: Fri Nov 27, 2020 9:03 pm    Post subject: Reply with quote

Hi,

For your split keyboard setup.
How did you set it up on the Korg R3? I.e. what is the voice mode that you are using?
_________________
microKORGXL, Kaossilator Pro, monotribe, SQ-1, volca fm, Kross 88 BK
Alesis SR18, Akai Miniak, Fender Strat, Line 6 Spider II 112, Zoom MS-50G
Back to top
View user's profile Send private message
slug
Senior Member


Joined: 03 Aug 2007
Posts: 370

PostPosted: Sat Nov 28, 2020 3:23 am    Post subject: Reply with quote

I dont have an R3 either, but can you just set pitch bend range to zero for that timbre? Page 26 of the manual.
Back to top
View user's profile Send private message
DiscoDean



Joined: 25 Nov 2020
Posts: 5

PostPosted: Sun Nov 29, 2020 2:20 am    Post subject: Reply with quote

Nealster wrote:
Hi DiscoDean!

Edited:
I first replied with how to do this on the Radias, then I realized you were asking about the R3.

I don't have an R3, but according to the manual on page 26, the R3 should have the Bend Range setting under "PITCH-B".
Change this setting to 0 for your lower timbre:



Hope this helps!


Actually yes this is how to do it, thank you! Not sure why it wasn't working the first time, but for sure once the timbres are split you can set the range of each separately.
Back to top
View user's profile Send private message
DiscoDean



Joined: 25 Nov 2020
Posts: 5

PostPosted: Sun Nov 29, 2020 2:22 am    Post subject: Reply with quote

Nealster wrote:
Hi DiscoDean!

Edited:
I first replied with how to do this on the Radias, then I realized you were asking about the R3.

I don't have an R3, but according to the manual on page 26, the R3 should have the Bend Range setting under "PITCH-B".
Change this setting to 0 for your lower timbre:



Hope this helps!


Actually YES this is how to do it. I'm not sure why it wasn't working the first time, but it's good now. THANK YOU
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Korg Forums Forum Index -> Korg RADIAS / R3 All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group