Korg Forums

keywhiz61 · Full Member Joined: 07 Mar 2011 Posts: 103

Where do I find the control to select different outputs for a program or combi?

X-Trade · Posted: Sun Jun 19, 2011 8:43 pm Post subject:

Based on my experience of other Korg workstations, this will be in the Effects routing (bus) pages.

Korg's architecture pretty much follows a kind of traditional studio approach, where your instruments run into effects or out to outputs, you have send (master) effects like you would on a mixer, for reverb/delay/chorus etc.

If the program you are using has some effects on it, you may want to look at the output of the effects it runs in to and set the output from the effects rather than from the program itself - which would bypass the effects.
_________________
Current Gear: Kronos 61, RADIAS-R, Volca Bass, ESX-1, microKorg, MS2000B, R3, Kaossilator Pro +, MiniKP, AX3000B, nanoKontrol, nanoPad MK II,
Other Mfgrs: Moog Sub37, Roland Boutique JX03, Novation MiniNova, Akai APC40, MOTU MIDI TimePiece 2, ART Pro VLA, Focusrite Saffire Pro 40.
Past Gear: Korg Karma, TR61, Poly800, EA-1, ER-1, ES-1, Kawai K1, Novation ReMote37SL, Boss GT-6B
Software: NI Komplete 10 Ultimate, Arturia V Collection, Ableton Live 9. Apple OSX El Capitan on 15" MacBook Pro

keywhiz61 · Full Member Joined: 07 Mar 2011 Posts: 103

Actually bypassing the effects is my goal here.

But I'm not finding any output routing in the effects section either.

X-Trade · Posted: Sun Jun 19, 2011 8:52 pm Post subject:

You see where you select which FX it goes to in the IFX Routing page? you should have the outputs in that selection too. I assume you're talking about combi mode?
_________________
Current Gear: Kronos 61, RADIAS-R, Volca Bass, ESX-1, microKorg, MS2000B, R3, Kaossilator Pro +, MiniKP, AX3000B, nanoKontrol, nanoPad MK II,
Other Mfgrs: Moog Sub37, Roland Boutique JX03, Novation MiniNova, Akai APC40, MOTU MIDI TimePiece 2, ART Pro VLA, Focusrite Saffire Pro 40.
Past Gear: Korg Karma, TR61, Poly800, EA-1, ER-1, ES-1, Kawai K1, Novation ReMote37SL, Boss GT-6B
Software: NI Komplete 10 Ultimate, Arturia V Collection, Ableton Live 9. Apple OSX El Capitan on 15" MacBook Pro

keywhiz61 · Full Member Joined: 07 Mar 2011 Posts: 103

Ah yes, I see it there! I was looking program mode.

Thanks!

X-Trade · Posted: Sun Jun 19, 2011 9:09 pm Post subject:

There should be a similar setting in Program mode. Try:
Common > IFX > Bus Select
_________________
Current Gear: Kronos 61, RADIAS-R, Volca Bass, ESX-1, microKorg, MS2000B, R3, Kaossilator Pro +, MiniKP, AX3000B, nanoKontrol, nanoPad MK II,
Other Mfgrs: Moog Sub37, Roland Boutique JX03, Novation MiniNova, Akai APC40, MOTU MIDI TimePiece 2, ART Pro VLA, Focusrite Saffire Pro 40.
Past Gear: Korg Karma, TR61, Poly800, EA-1, ER-1, ES-1, Kawai K1, Novation ReMote37SL, Boss GT-6B
Software: NI Komplete 10 Ultimate, Arturia V Collection, Ableton Live 9. Apple OSX El Capitan on 15" MacBook Pro

Mike Conway · Posted: Sun Jun 19, 2011 9:14 pm Post subject:

On the IFX page. There are a couple of ways to do it - pre-Insert Effect or Post-Insert Effect.

Pre:

Press IFX tab, then ROUTING1 tab.

Under BUS SELECT (IFX/INDIV.OUT ASSIGN), you select the output, which can be L/R, any IFX and outs 1 - 4.

Post Effect:

Press the IFX tab, then INSERT FX tab. You should see all 12 Insert FX. To the right of each Insert you will see PAN, BUS SEL., REC BUS., etc. BUS SEL. is where you select the output - L/R 1 - 4.

EDIT: my wife and 3 kids walked in with all these cool Father's Day cards and I didn't realize the post got all these responses, already! Very Happy

keywhiz61 · Full Member Joined: 07 Mar 2011 Posts: 103

Yep! Found it in both modes. Thanks!