View previous topic :: View next topic |
Author |
Message |
7zark7 Junior Member
Joined: 09 Jul 2015 Posts: 62 Location: Chicago
|
Posted: Sat Sep 19, 2015 4:54 am Post subject: |
|
|
jbvdb493 wrote: | Well it doesn't look that bad! It's just too bad you couldn't get them to write on the overlay what the pad shortcuts are! |
I know. I am probably going to try to make translucent labels to go under and above the pads. |
|
Back to top |
|
|
7zark7 Junior Member
Joined: 09 Jul 2015 Posts: 62 Location: Chicago
|
Posted: Sat Sep 19, 2015 4:55 am Post subject: |
|
|
Hugo wrote: | Looks awesome! One question, though; how thick are these overlays? Do they affect the operation of the unit? |
It is very thin. No problems yet. |
|
Back to top |
|
|
Hugo Platinum Member
Joined: 23 Jun 2006 Posts: 809
|
Posted: Sat Sep 19, 2015 10:14 am Post subject: |
|
|
7zark7 wrote: | Hugo wrote: | Looks awesome! One question, though; how thick are these overlays? Do they affect the operation of the unit? |
It is very thin. No problems yet. |
Cool, thanks
Is it difficult to get it to fit correctly? |
|
Back to top |
|
|
7zark7 Junior Member
Joined: 09 Jul 2015 Posts: 62 Location: Chicago
|
Posted: Sun Sep 20, 2015 12:20 am Post subject: |
|
|
Yeah, It takes a few tries. I intend to lay it down again at some point. Because visually there are a few places where there is slightly more space on one side than the other. In my picture you might notice to the left of the mod knob and amp level knob that there is slightly more black than the right. Also left of the chord, step jump, and pattern set buttons. This really is about getting the placement just right though. All of the pads buttons and knobs line up and have enough space. You have to really be in the right position with the right leverage and ability to turn and move the electribe as you apply the skin, while smoothing out bubbles and making sure each cutout is centered. I applied mine while it was hooked up and in a difficult position to work on. Seems that you can re-apply the skin multiple times though. |
|
Back to top |
|
|
DodgingRain
Joined: 25 May 2009 Posts: 33
|
Posted: Sun Sep 20, 2015 1:22 am Post subject: |
|
|
Quote: | I know. I am probably going to try to make translucent labels to go under and above the pads. | You could design that into your overlay, but it would be hard to find the space without using really small text. |
|
Back to top |
|
|
Hugo Platinum Member
Joined: 23 Jun 2006 Posts: 809
|
Posted: Sun Sep 20, 2015 1:39 am Post subject: |
|
|
7zark7 wrote: | Yeah, It takes a few tries. I intend to lay it down again at some point. Because visually there are a few places where there is slightly more space on one side than the other. In my picture you might notice to the left of the mod knob and amp level knob that there is slightly more black than the right. Also left of the chord, step jump, and pattern set buttons. This really is about getting the placement just right though. All of the pads buttons and knobs line up and have enough space. You have to really be in the right position with the right leverage and ability to turn and move the electribe as you apply the skin, while smoothing out bubbles and making sure each cutout is centered. I applied mine while it was hooked up and in a difficult position to work on. Seems that you can re-apply the skin multiple times though. |
Ok, thanks for the info |
|
Back to top |
|
|
7zark7 Junior Member
Joined: 09 Jul 2015 Posts: 62 Location: Chicago
|
Posted: Sun Sep 20, 2015 6:48 am Post subject: |
|
|
DodgingRain wrote: | You could design that into your overlay, but it would be hard to find the space without using really small text. |
I know, but the design interface was confusing to me. It seemed like too much trouble. |
|
Back to top |
|
|
wikter
Joined: 30 Dec 2015 Posts: 11
|
|
Back to top |
|
|
wikter
Joined: 30 Dec 2015 Posts: 11
|
Posted: Mon Nov 28, 2016 8:00 pm Post subject: |
|
|
How can I submit an image that is referred by an Hhtml?
Holy Sh**T!!
Done!
|
|
Back to top |
|
|
boe_dye
Joined: 09 Jan 2017 Posts: 1
|
Posted: Mon Jan 09, 2017 11:18 pm Post subject: Does anyone have the vectors or shop files? |
|
|
Really like this skin a lot and was wondering if anyone had the vectors or shop files available, and would be willing to share.
Thanks! |
|
Back to top |
|
|
wikter
Joined: 30 Dec 2015 Posts: 11
|
Posted: Sat Apr 01, 2017 8:36 pm Post subject: |
|
|
Hi, I thought I'd post it here before, but I only posted the image. Well.. here it is the link to download directly that PSD file to manage labels, layers, colours and anything and get a skint just like this:
(First, the link to the blog post containing the file, please tell me if links don't work)
http://mvxsynths.blogspot.com.es/2017/04/electribe-2-skins.html
|
|
Back to top |
|
|
|