Korg Forums

Now Kronos is connected but the korg driver setup utility
is popping every 10 min prompting to install, it's installed already !

Ron wrote:I had a similar problem. Check out link below to Pa4x forum. Hope it helps.

http://www.korgforums.com/forum/phpBB2/ ... p?t=120192

Ron Thank you man you're amazing

Ron wrote:I had a similar problem. Check out link below to Pa4x forum. Hope it helps.

http://www.korgforums.com/forum/phpBB2/ ... p?t=120192

Thank you Ron I’ll try it.

Hi, after windows 10 update my kronos stopped showing in cubase I re-installed the midi driver but the same problem, when I tried to un install the USB driver through ( Korg software it's not showing any korg devise connected). please any ideas ? this screen shot images https://imgur.com/gallery ...

Hi, some parameters in combi mode are not responding.
I reset the keyboard ( Turn on while holding 0+Enter ). Still the same problem. Any ideas?

Parameters not responding ( midi Chanels, zones, status)
I triad Dial, Up & Down botton, slider.

Please help

Reuben wrote:The plastic degrades over time and is a known problem and I don’t think it can be cleaned off.
The only bit you really need to touch is the area below the joystick. I have put some black tape on this section.

Thank you, I think I have to put tape too.

Hey guys,
what's the best way to clean the keyboard plastic ( joy stick area ) it's very sticky & dirty. I used water and soap, didn't work. it's like melted plastic I can't slide my fingers on it.
any ideas ??

Hi, I installed new third party sounds on my kronos x, now I changed my mind, I installed factory preload sounds KSC. The factory sounds are there but the old third party patches names didn’t reset. Still there without samples. How to hard reset I want to reset kronos like the original state. Please ...

I found one more thing, when assigning all the sounds in the 16 tracks and save the song. Actually, PA is not saving any thing. only if there is actual midi notes recorded in PA. Other than that PA won't recognize the tracks, which is mean I can't use it as sound source for External Sequencer. is ...

I found one more thing, when assigning all the sounds in the 16 tracks and save the song. Actually, PA is not saving any thing. only if there is actual midi notes recorded in PA. Other than that PA won't recognize the tracks, which is mean I can't use it as sound source for External Sequencer. is it ...

Drums must be always on track 10. That's midi standard. is this happen only to this track? Try assign any other (not Drums) sound. Did you try play it ? :wink: Yes, the same thing happened to other tracks, I play all the tracks and check them before Reloading. I meant after saving, when you first ...

Ok, let’s start over. I want to use pa sounds to record midi in cubase. Before connecting to PC. I prepare the tracks in PA3. In sequencer mode I assigned Drums to the first track. Saved the song. When I try to check my setup is saved, I reload the saved song then ( every thing is gone ) the first t ...

Ok, let's start over, I'm kinda lost what you trying to do. First you said you trying to use Pa3x as source for external sequencer. Hi, I’m trying to use PA3X as sound source for external sequencer ( Cubase9 ) But Pa3x keep reseting the instruments in the tracks even after saving the song. Please h ...

Try to use filters on Pa3x Midi IN Channels. Filter Prg. Change . That's should stop changing sounds on Pa3x. In Global Midi/ General Controls you should have few presets, one of them is External Sequencer (not sure), you can try there, maybe changing preset will help. Anyway, to control Pa3x from ...

Try to use filters on Pa3x Midi IN Channels. Filter Prg. Change . That's should stop changing sounds on Pa3x. In Global Midi/ General Controls you should have few presets, one of them is External Sequencer (not sure), you can try there, maybe changing preset will help. Anyway, to control Pa3x from ...