Page 1 of 1
Routing CX-3 programs into output 1 of Kronos
Posted: Sat Oct 03, 2020 7:33 pm
by mrvegas
I use a separate Leslie simulator pedal with my Kronos organ sounds so I have manually configured certain programs (Cat on a Mojo, etc) to be output to channel 1 instead of the normal stereo left and right outputs.
What I have noticed is that the volume knob in the upper left corner of the Kronos does not control the volume of the programs routed to channel 1. Is this normal? Is there a way to enable the keyboards volume knob to control the volume of the programs routed into channel 1?
Posted: Sat Oct 03, 2020 8:27 pm
by voip
This is normal behaviour. The Main Volume control is an analogue control, and is not capable of being linked to the other outputs. It might be worth considering using an Expression pedal.
.
Posted: Sat Oct 03, 2020 11:18 pm
by mrvegas
ok, thank you!
Posted: Sun Nov 29, 2020 3:53 pm
by engineerjoel
So, would it be possible to assign one of the rotary knobs to control the volume of an individual output??
Posted: Mon Nov 30, 2020 9:29 am
by Liviou2004
mrvegas wrote: Is there a way to enable the keyboards volume knob to control the volume of the programs routed into channel 1?
Yes, you can do it by using your Prog in a Combination Timbre. Set the Timbre to one of the individual output bus and set the volume with the Timbre slider.
Posted: Tue Dec 01, 2020 8:39 pm
by engineerjoel
Liviou2004 wrote:mrvegas wrote: Is there a way to enable the keyboards volume knob to control the volume of the programs routed into channel 1?
Yes, you can do it by using your Prog in a Combination Timbre. Set the Timbre to one of the individual output bus and set the volume with the Timbre slider.
Does the volume have to be controlled by a Slider? Can I assign one of the rotary knobs to control volume of a Timbre sent out an individual out?
Posted: Wed Dec 02, 2020 7:29 am
by Liviou2004
engineerjoel wrote:Liviou2004 wrote:mrvegas wrote: Is there a way to enable the keyboards volume knob to control the volume of the programs routed into channel 1?
Yes, you can do it by using your Prog in a Combination Timbre. Set the Timbre to one of the individual output bus and set the volume with the Timbre slider.
Does the volume have to be controlled by a Slider? Can I assign one of the rotary knobs to control volume of a Timbre sent out an individual out?
No, as far as I know, the timbre volumes in a Combination are controlled by the sliders.
Posted: Tue Dec 29, 2020 12:07 am
by engineerjoel
Well that sucks... In Combination mode, if I had several layers going on —including an organ—I was wanting to reserve all nine control sliders for drawbars for the organ, and use one of rotary knobs to control organ volume.
Posted: Tue Dec 29, 2020 1:13 am
by tunaman
Use an expression pedal?
Posted: Sat Jan 02, 2021 5:24 pm
by KingKronos
You can control the volume with knob 3.
When you select tone adjust and use the sliders as drawbars, knob 3 will control the expression level.
Posted: Sun Jan 03, 2021 6:38 pm
by jtern
Maybe you can route the organ through an IFX with a (dummy) compressor (ratio 1:1), with one of the realtime knobs (5-8) controlling the gain of the effect?
Let me know if you don’t understand what I mean, and I’ll explain in more detail.
Posted: Fri Jan 08, 2021 6:44 pm
by KingKronos
engineerjoel wrote:Well that sucks... In Combination mode, if I had several layers going on —including an organ—I was wanting to reserve all nine control sliders for drawbars for the organ, and use one of rotary knobs to control organ volume.
Did knob 3 work for you?