CC midi signal to change pattern on the electribe emx2?

Buska · Post by **Buska** » Fri Jan 23, 2015 11:52 am

Is this possible? If so which channel or program number?

dutchcow · Post by **dutchcow** » Fri Jan 23, 2015 12:23 pm

It is possible. At least from within Ableton I been able to change patterns on the e2 using the pgm parameter on the midi track.

Buska · Post by **Buska** » Fri Jan 23, 2015 12:38 pm

dutchcow wrote:It is possible. At least from within Ableton I been able to change patterns on the e2 using the pgm parameter on the midi track.

Awesome thanks

Poumtschak · Post by **Poumtschak** » Fri Jan 23, 2015 1:14 pm

I believe Tarekith also got it on FB :
http://www.korgforums.com/forum/phpBB2/ ... 949#624949

jim555 · Post by **jim555** » Fri Jan 23, 2015 5:29 pm

Poumtschak wrote:I believe Tarekith also got it on FB :
http://www.korgforums.com/forum/phpBB2/ ... 949#624949

I'm the Jim Fiive who posted that on FB. Electribe's pattern numbers are mapped to midi program number. Program number 0 is pattern 1, program number 1 is pattern 2 and so on.

One thing I found out was that the Electribe doesn't respond to bank message. At least not from my Octatrack sequencer.

What happens is when you are on patterns above 128, Electribe will change to pattern 129 to 256 when you send program number 0 to 127. Something you should be aware of when you are setting up your pattern changes from the external sequencer.

SMK · Post by **SMK** » Tue Jan 27, 2015 10:35 am

jim555 wrote:
Poumtschak wrote:I believe Tarekith also got it on FB :
http://www.korgforums.com/forum/phpBB2/ ... 949#624949
I'm the Jim Fiive who posted that on FB. Electribe's pattern numbers are mapped to midi program number. Program number 0 is pattern 1, program number 1 is pattern 2 and so on.

One thing I found out was that the Electribe doesn't respond to bank message. At least not from my Octatrack sequencer.

What happens is when you are on patterns above 128, Electribe will change to pattern 129 to 256 when you send program number 0 to 127. Something you should be aware of when you are setting up your pattern changes from the external sequencer.

Thanks Jim for clearing that up. Great tip to know!

jericho · Post by **jericho** » Wed Feb 17, 2016 10:36 pm

I'm trying to get a program change to happen via Ableton to the Electribe 2. I've tried firing a midi clip in session and arrangement view, but it won't change the pattern on the E2. My midi pref is set to receive midi on the E2. I'm stumped...

PureSecksPirate · Post by **PureSecksPirate** » Thu Feb 18, 2016 2:04 am

You are looking for a program change. In your midi clip, go to your "notes" tab and there is a window with "pgm --". Click on that and type in the number that corresponds with the pattern on your electribe2.

jericho · Post by **jericho** » Thu Feb 18, 2016 7:25 am

PureSecksPirate wrote:You are looking for a program change. In your midi clip, go to your "notes" tab and there is a window with "pgm --". Click on that and type in the number that corresponds with the pattern on your electribe2.

I did this. I've tried different pgm numbers. I have ableton playing the E2 on 16 separate midi channels and have tried clips on different channels, but the pattern doesn't change. The note data transfers just fine though, so I know it's receiving midi

jericho · Post by **jericho** » Sat Feb 20, 2016 6:04 am

I figured it out. In order for the program change to happen on the E2, the midi channel outputting from ableton must match the global midi channel on the E2. This can be set on p.4 of the global parameters on the E2.

Korg Forums

CC midi signal to change pattern on the electribe emx2?

CC midi signal to change pattern on the electribe emx2?

Program Changes: Ableton -> E2

Program Changes: Ableton -> E2