Page 1 of 2
SQ-1 and Fl studio
Posted: Wed Apr 15, 2015 6:25 pm
by lado
Hello Everybody.
I just got SQ-1 and have small problem with fl studio.
Everything is synced just when i press play in fl studio korg doesnot start with it. After Fl studio is started i have to press extra play on korg to start it.
In ableton it works normally.
Please any ideas ?
Thank you
Posted: Wed Apr 15, 2015 7:52 pm
by lado
anybody ?
Posted: Wed Apr 15, 2015 7:53 pm
by lado
anybody ?
Posted: Wed Apr 15, 2015 9:59 pm
by lado
when i press stop in fl studio it also stops SQ.The only problem is start ! I thinks its not recieveing midi from Fl.Anybody had the same problem ?Or i am the only one who is using this s**t software ?
Posted: Wed Apr 15, 2015 10:43 pm
by Spheric El
I've used FL.A few years ago now,but I do remember it had a different way of working/starting.This is no real help,but at the time I couldn't sync it to other software DAWs using its little FL VST thingy(in the other software- Orion).I ended up pressing start first in FL then when I trigger start on Orion it would kick in. Or something like that..
It's a bit of an unusual UI.
Can you try to use your Korg as master?
Does it have midi out?
If so try setting FL to external sync(midi clock)and use SQ to trigger start.
Posted: Thu Apr 16, 2015 6:49 am
by lado
yes it have midi out but sq as a master works not so good.
Any others ideas ?
I spent whole night but no result
Posted: Thu Apr 16, 2015 7:02 am
by chris-korg
I do not know FL Studio either but suggest you try the following:
Once you connected your computer to SQ1 press PLAY on the SQ1.
If everything works as I expect the SQ1 goes into "waiting mode" and does not start immediately.
Then you press start on FL Studio which should then let SQ1 start as well...
If this works then you need to press PLAY twice whenever you stop the sequence via FL Studio to set SQ1s sequence back to step 1.
Hope that helps
Posted: Thu Apr 16, 2015 7:15 am
by lado
no its not working like that.
I am doing video so it will be more clear to understand what i mean.
Posted: Thu Apr 16, 2015 7:20 am
by lado
https://www.youtube.com/watch?v=cO_UlhPwoAM
I press play on keyboard and eveyrthing starts exept Korg !
Posted: Thu Apr 16, 2015 2:24 pm
by lado
FROM KORG:
Hello,
It sounds like FL studio is not transmitting Start/Stop messages. Please find the appropriate settings in FL studio to change this.
Best regards,
Korg USA, Inc.
Posted: Thu Apr 16, 2015 3:37 pm
by Spheric El
Have you tried the various preference menus in FL with anything about midi.Tick any boxes you can find?
Try finding a dedicated FL forum on line also,because I did have a similar problem back then,so there must be others.It doesn't behave like most DAWs with that start (from what I remember) and there may well be something we have both missed.
Posted: Thu Apr 16, 2015 5:04 pm
by lado
any other ideas ?
Posted: Fri Apr 17, 2015 6:59 am
by chris-korg
This is what Korgs FAQ say:
Synchronizing the SQ-1 to a PC or a MIDI device
To synchronize the SQ-1 to an external device, you can use either of two methods: USB-MIDI connection or SYNC IN connection. USB-MIDI connection allows sequencer start/stop and tempo synchronization. SYNC IN connection allows only tempo synchronization. If USB-MIDI and SYNC IN are both connected, SYNC IN takes priority as the synchronization clock. However, the SYNC IN signal is a clock only for tempo synchronization. Since SYNC IN does not provide sequencer start/stop functionality, start/stop operations performed on the SQ-1 itself or via USB-MIDI are valid even when the SQ-1 is synchronized via SYNC IN.
Posted: Fri Apr 17, 2015 9:41 am
by lado
I know what korg says....
Fl can see Korg sq but star doesnot work.Stop works but start noooo....
Posted: Fri Apr 17, 2015 9:43 am
by lado
everything works perfect,its in sync it stops when i press stop in fl.It just doesnot start.Please check video i posted.