|
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
Tobando
Joined: 10 Jun 2018 Posts: 3
|
Posted: Sun Jun 10, 2018 12:59 pm Post subject: Troubleshooting 1st gen nanoKey / nanoPad |
|
|
Hello everyone,
I am writing about a problem with two nanoKONTROL devices.
I recently came into possession of a nanoKey and a first-generation nanoPad. Once attached to the computer, the devices are recognized as actually nanoKeys and nanoPads, but I find it impossible to use them in any way. The physical LEDs are all lit simultaneously (Octave Down/Up/CC Mode for the nanoKey, the 4 scenes for the nanoPad) and the devices do not respond to any key.
However, they are recognized by the computer (Macbook Pro with OSX 10.12.6) even though, apparently, they are only powered (the computer does not recognize any input signal). In the MIDI Audio configuration they are detected, but I can't change Midi In/Out port. Using the Korg Kontroller Editor, however, it doesn't even detect them as connected to the computer. I have already tried to install the latest version of the MIDI-USB drivers available on korg's website, but this has not changed anything.
Unfortunately, not being the first owner of the devices and having received them as already broken, I can not be sure of the cause of the problem.
However, it does NOT seem to be a hardware problem. My main suspicion is that, in some way, the firmware/kernel driver of the devices has been deleted, and so they are now "inert", but obviously I'm not sure this is possible.
Can anyone help me out? |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3792
|
Posted: Mon Jun 11, 2018 2:16 pm Post subject: |
|
|
A factory reset is worth trying. |
|
Back to top |
|
|
Tobando
Joined: 10 Jun 2018 Posts: 3
|
Posted: Mon Jun 11, 2018 6:12 pm Post subject: |
|
|
voip wrote: | A factory reset is worth trying. |
You mean, on the nanoKeys, by holding down the octave down / up and the mod keys while connecting it to the computer right? In that case, I fear it's not working, all the LEDs stay lit and nothing happens :/
I haven't found how to perform it on the nanoPad though, any suggestion?
The official support in my country just answered my e-mail saying it's probably a hardware problem, even though that seems strange to me (I have performed a couple tests with oscilloscopes and stuff and, at least for the nanoPad, the pads seems to work properly, at least physically..) |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3792
|
Posted: Mon Jun 11, 2018 9:28 pm Post subject: |
|
|
That is the correct key combination for the nanoKEY.
For the nanoPAD, the factory reset key combination is <Hold> <Flam> and <Scene>, whilst powering up.
It's a bit of a long shot, but powering the controllers from a powered USB hub might be worth trying. |
|
Back to top |
|
|
Tobando
Joined: 10 Jun 2018 Posts: 3
|
Posted: Tue Jun 12, 2018 6:26 am Post subject: |
|
|
voip wrote: | That is the correct key combination for the nanoKEY.
For the nanoPAD, the factory reset key combination is <Hold> <Flam> and <Scene>, whilst powering up.
It's a bit of a long shot, but powering the controllers from a powered USB hub might be worth trying. |
Just tried the factory reset and it didn't work, and even the powered USB hub proved useless :/
At this point I'm guessing it actually IS an hardware problem, even though it seems so strange that they both suffer from the same issue. And as I'm not the original owner, I can't really know what happened that put them in this state, so I'm giving up.
Anyways, thanks a lot for your answers |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|