View previous topic :: View next topic |
Author |
Message |
icecoldrocker
Joined: 12 Oct 2021 Posts: 49 Location: texas
|
Posted: Thu May 18, 2023 11:56 am Post subject: Samples Load but Not Into the Program Location... |
|
|
ok so with the infinite custom relations and wisdom both from and of Korg I chose to sample some sounds from the KORG M3 only thing is that:
1. Yes, the samples have been copied to the in-ter-nal SSD
2. Yes, these samples are selected to auto-load
3. Yes, I have the program location in a capital letter bank
So now every time I go to use that program in a song I am having to keep reassigning the samples to that program location. I did not have this happening with M3 _________________ Korg Poly 800
Yamaha V-50
Korg X-3 🙂
Korg Trinity Pro 🚀 🙂
Korg Triton Extreme 😮
Korg M3 🤔
Korg Nautilus 👑
Korg Gadget ❤️
Cubase Pro 🚀
Reason 11❤️🇸🇪
Logic Pro 💟 |
|
Back to top |
|
|
Dan Stesco Approved Merchant
Joined: 11 Dec 2009 Posts: 639 Location: Bucharest
|
Posted: Thu May 18, 2023 2:35 pm Post subject: |
|
|
If I understand well, you need to select the samples bank in program OSC after restart the Nautilus ? Please describe more about that behaviour. _________________ http://www.danstesco.ro |
|
Back to top |
|
|
icecoldrocker
Joined: 12 Oct 2021 Posts: 49 Location: texas
|
Posted: Fri May 19, 2023 12:29 am Post subject: |
|
|
[ i said ]
the samples load in to RAM
however samples will not load to the program location
i keep having to reassign the samples to the PROGRAM LOCATION
of course the sounds/samples will will be there at S000 however after powering down the Nautilus and turning it back on the samples WILL NOT LOAD TO S000 i have to reassign then write to the program again however those samples will not load to the location AFTER POWERING BACK ON _________________ Korg Poly 800
Yamaha V-50
Korg X-3 🙂
Korg Trinity Pro 🚀 🙂
Korg Triton Extreme 😮
Korg M3 🤔
Korg Nautilus 👑
Korg Gadget ❤️
Cubase Pro 🚀
Reason 11❤️🇸🇪
Logic Pro 💟 |
|
Back to top |
|
|
tunaman Senior Member
Joined: 28 Nov 2019 Posts: 427
|
Posted: Fri May 19, 2023 3:04 pm Post subject: |
|
|
You are saving the Program after configuring the samples, correct?
You are then saving the PCG data, correct? |
|
Back to top |
|
|
icecoldrocker
Joined: 12 Oct 2021 Posts: 49 Location: texas
|
Posted: Fri May 19, 2023 3:26 pm Post subject: WOW |
|
|
yes I have done this I have saved the PCG however every time I go to load it back in the samples will not load in to the program location I keep having to reassign the samples to the program location over and over again and the samples are set to auto load and yes the samples are saved to the internal SSD _________________ Korg Poly 800
Yamaha V-50
Korg X-3 🙂
Korg Trinity Pro 🚀 🙂
Korg Triton Extreme 😮
Korg M3 🤔
Korg Nautilus 👑
Korg Gadget ❤️
Cubase Pro 🚀
Reason 11❤️🇸🇪
Logic Pro 💟 |
|
Back to top |
|
|
tunaman Senior Member
Joined: 28 Nov 2019 Posts: 427
|
Posted: Sun May 21, 2023 4:25 pm Post subject: |
|
|
Not entirely sure of the end objective, but I’ll throw this out in case it helps… it is a post from a thread in the Kronos forum which might be applicable:
tunaman wrote: | ronnfigg wrote: | Did you "Save Sampling Data" in Disk Mode (Page Menu Commands in the "Save" tab)? |
This is likely the issue, based on my growing pains. The sample needs to be saved to disk prior to converting to MS, else the sample won’t be linked and it will be lost after shutdown.
Here is the workflow I’m using, thanks to a bunch of research, failed attempts, and good posts and videos from helpful folks:
1. Go into Global, deselect all KSC files (note which are already unchecked if they aren’t all auto-loaded, so that you can set it back up once you’re done), and press the auto-load button;
2. Go into Disk mode and load the sample file;
3. Go into Sampling mode and add the sample to the new sample page;
4. Assign key(s) as appropriate;
5. Rename the MS
6. Go into Disk mode and save Sampling Data - I’m using the Sampling Mode Data, All, and Force new User Sample Bank ID options;
7. Go into Global mode and add the new KSC to the list; I’m also selecting the rest of the KSC files to auto-load here so that I don’t forget;
8. Go back into Sampling mode and select the menu option to convert MS to Program;
9. Go back into Disk mode and save the PCG data;
This workflow seems to be working well for me - hope this helps? |
Hope this helps? |
|
Back to top |
|
|
|