|
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
ChrisDuncan Senior Member
Joined: 17 May 2018 Posts: 389
|
Posted: Fri Sep 01, 2023 4:17 pm Post subject: Controller slider 5 and 6 not transmitting volume on ext |
|
|
I have the Kronos set up with a combi that points to the Fantom. Each track is set to ext on that midi channel, e.g. 1, 2, 3, etc.
When I move the sliders, the volume on the Fantom zone updates accordingly. This works for all 16 channels, with the exception of 5 and 6.
I've double checked the combi and they're set up just like the other channels.
I also set the front panel to ext and recorded midi in Cubase. All 16 sliders, including 5 and 6, transmit CC 78 in that scenario, so it would seem that the sliders are functioning.
I thought it might be something I did on the Fantom, but I first had a Fantom-06 this week, and I've now replaced that with a Fantom 6. It behaves the same in both cases, so that would seem to point to the Kronos.
I suppose there could be some kind of failure in the Kronos on 5 and 6 that keeps it from transmitting CC7, but that seems odd since they transmit to Cubase. Also, it's usually more likely that I've screwed something up myself than having a hardware issue.
At this point I'm out of ideas on how to debug this. Anyone have any thoughts? _________________ Studio: Cubase 13 | Windows 10 | Yamaha TF5 | Mackie MCU | CMC AI, QC
Keyboard Station: Kronos 2 88 | Fantom 7 | JV 2080 | Cubase 13 | Windows 10 | Focusrite 18i20 | CMC TP
~~~~~~~~~~~~~~~~~~~~~~~
Chris Duncan
Atlanta, GA, USA, Earth |
|
Back to top |
|
|
CliveJ Junior Member
Joined: 30 Dec 2020 Posts: 91
|
Posted: Fri Sep 01, 2023 11:21 pm Post subject: |
|
|
Is the Kronos connected to Cubase exactly the same as the Fantom (ie USB or MIDI)? If so then you have already proved that Kronos is transmitting correctly so the issue must be in the Fantom - Unless you are using a MIDI splitter/merge box, in which case I would take it out of the loop temporarily. _________________ Now let’s think of a reason why it CAN be done... |
|
Back to top |
|
|
ChrisDuncan Senior Member
Joined: 17 May 2018 Posts: 389
|
Posted: Sat Sep 02, 2023 1:54 am Post subject: |
|
|
Hey, Clive.
Good catch. I talk to Cubase via USB but the Fantom via 5 pin, and I do have a midi merger in the middle.
I plugged a cable from the back of the Kronos to the Fantom and still had the same problem. However, I forgot to test going 5 pin to Cubase to see if that was any different. Will do that tomorrow.
Appreciate the help! _________________ Studio: Cubase 13 | Windows 10 | Yamaha TF5 | Mackie MCU | CMC AI, QC
Keyboard Station: Kronos 2 88 | Fantom 7 | JV 2080 | Cubase 13 | Windows 10 | Focusrite 18i20 | CMC TP
~~~~~~~~~~~~~~~~~~~~~~~
Chris Duncan
Atlanta, GA, USA, Earth |
|
Back to top |
|
|
ChrisDuncan Senior Member
Joined: 17 May 2018 Posts: 389
|
Posted: Sun Sep 03, 2023 1:32 am Post subject: |
|
|
Hey, Clive.
I followed up and tested Cubase from 5 pin and there were no problems.
However, as I poked around in the combi, I noticed that in two of the midi filter tabs, the entire columns for channesl 5 and 6 were unchecked. I checked them, and the Fantom responded on those channels like every other.
I don't know how those got unchecked as I rarely fool with the midi filters. Most likely I copied a combi that was provided with the Kronos and filed the serial numbers off to use for another scenario.
As suspected, the problem ended up being cockpit error, which comes as a surprise to no one.
Thanks for the help, man! _________________ Studio: Cubase 13 | Windows 10 | Yamaha TF5 | Mackie MCU | CMC AI, QC
Keyboard Station: Kronos 2 88 | Fantom 7 | JV 2080 | Cubase 13 | Windows 10 | Focusrite 18i20 | CMC TP
~~~~~~~~~~~~~~~~~~~~~~~
Chris Duncan
Atlanta, GA, USA, Earth |
|
Back to top |
|
|
CliveJ Junior Member
Joined: 30 Dec 2020 Posts: 91
|
Posted: Mon Sep 04, 2023 8:57 am Post subject: |
|
|
Glad you’re sorted _________________ Now let’s think of a reason why it CAN be done... |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|