View previous topic :: View next topic |
Author |
Message |
sunriser111671 Full Member
Joined: 17 Jul 2013 Posts: 129 Location: Michigan USA
|
Posted: Tue Jul 14, 2015 4:53 pm Post subject: Showing Off My Custom M1 |
|
|
So, I was tired of the somewhat ugly black-on-green display of my Korg M1 and decided to replace it with the ultra-cool white on blue display (seems to actually match the M1 case better!)
So here's me being a show-off and posting my cool new display:
The picture really doesn't do it justice. Maybe I'll figure out how to get my camera to get a better picture of it and post a better pic. |
|
Back to top |
|
|
the_crimson_thunder Junior Member
Joined: 18 Nov 2014 Posts: 92 Location: Germany
|
|
Back to top |
|
|
sunriser111671 Full Member
Joined: 17 Jul 2013 Posts: 129 Location: Michigan USA
|
Posted: Wed Jul 15, 2015 3:38 am Post subject: |
|
|
I ordered it from a place called crystalfontz for 25 bucks. They were very helpful when i ran into a problem with wiring.
If enough people show interest in doing this, i can post some instructions. It wasn't a straightforward replacement. Hardware install was a snap as it fit nicely into the original location, but the wiring required some customization... |
|
Back to top |
|
|
the_crimson_thunder Junior Member
Joined: 18 Nov 2014 Posts: 92 Location: Germany
|
Posted: Wed Jul 15, 2015 6:14 pm Post subject: |
|
|
Quote: | I ordered it from a place called crystalfontz |
Ah ok - I came across this name before - will take a closer look on their website...
Quote: | If enough people show interest in doing this, i can post some instructions. |
As for me I'm always interested in getting such informations
Thx for your reply |
|
Back to top |
|
|
sunriser111671 Full Member
Joined: 17 Jul 2013 Posts: 129 Location: Michigan USA
|
Posted: Wed Jul 29, 2015 12:22 am Post subject: |
|
|
Well here's the short of it:
The new LED backlight connection is right next to the display interface soldered connection. I spliced into the cable on the KLM-1269 5VDC connector (CN9) and feed the wires to the LED backlight solder points (A & K). The existing connector on the original LCD lined up perfectly after that to power the chip and update digit display.
The big issue,however is the potentiometer for the contrast adjustment: It was using a 6-10VDC signal and the new LED LCD requires 3-5VDC. I therefore removed the resistors at the potentiometer(R11,12,13) to open the 6-10VDC circuit and soldered 5VDC +/- feed wires to each leg of the pot.
After that, my super-cool blue display worked like a champ! |
|
Back to top |
|
|
jbeliz Full Member
Joined: 10 Jul 2010 Posts: 194 Location: Washington State
|
Posted: Thu Jul 30, 2015 2:40 pm Post subject: |
|
|
Awesome, thanks for sharing. _________________ Korg Kronos 2,Korg Oasys 76, Korg 01W/fd, Korg im1 ipad, Korg Triton Extreme, Korg Triton Studio, Korg M3, Roland Integra 7, Yamaha Montage 7, Roland Fantom 6, Korg Nautilus, Korg PA4X, Korg Kross 2 |
|
Back to top |
|
|
the_crimson_thunder Junior Member
Joined: 18 Nov 2014 Posts: 92 Location: Germany
|
Posted: Sat Nov 05, 2016 11:41 pm Post subject: My 'Cool Blue' Display-Upgrade M1 & M1REX |
|
|
Hi Guys,
here's the result of the 'Cool Blue' Display-Upgrade of my M1 & M1REX synths...
|
|
Back to top |
|
|
sunriser111671 Full Member
Joined: 17 Jul 2013 Posts: 129 Location: Michigan USA
|
Posted: Fri Nov 11, 2016 2:20 pm Post subject: |
|
|
crimson,
Nice job! You were able to get better pictures than I!
Did you end up going with the crystalfontz display? |
|
Back to top |
|
|
the_crimson_thunder Junior Member
Joined: 18 Nov 2014 Posts: 92 Location: Germany
|
Posted: Fri Nov 11, 2016 4:55 pm Post subject: |
|
|
Hi sunriser,
good to see you on the forum again...
sunriser111671 wrote: | You were able to get better pictures than I! | The secret is: use flash!
Quote: | Did you end up going with the crystalfontz display? |
No, got mine from BuyDisplay - it's an EastRising ERM4002-1 Series display. I will write some install notes and after converting to PDF I'll make them public here... as soon as I find some time... |
|
Back to top |
|
|
John01W Platinum Member
Joined: 13 Dec 2002 Posts: 1301 Location: Tejas
|
Posted: Fri Nov 11, 2016 9:49 pm Post subject: |
|
|
Lookin' good man! |
|
Back to top |
|
|
the_crimson_thunder Junior Member
Joined: 18 Nov 2014 Posts: 92 Location: Germany
|
Posted: Sat Nov 12, 2016 7:05 pm Post subject: |
|
|
I know... |
|
Back to top |
|
|
|