|
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
brandon Junior Member
Joined: 20 Sep 2008 Posts: 52
|
Posted: Sat Jun 29, 2013 7:53 am Post subject: switch vibrato |
|
|
hey guys i copied a patch setting from the manual for wheel controlled vibrato, which is cool but i would like to assign it to the momentary switch and use the wheel for pitch. when i simply changed the patch so that the switch is the source, i get vibrato normally and it stops when i press the switch. can't seem to reverse it as i don't really know what i'm doing that well.
any ideas would be great
thanks |
|
Back to top |
|
|
plosive Full Member
Joined: 08 Feb 2008 Posts: 248
|
Posted: Fri Jul 05, 2013 11:10 am Post subject: Re: switch vibrato |
|
|
brandon wrote: | hey guys i copied a patch setting from the manual for wheel controlled vibrato, which is cool but i would like to assign it to the momentary switch and use the wheel for pitch. when i simply changed the patch so that the switch is the source, i get vibrato normally and it stops when i press the switch. can't seem to reverse it as i don't really know what i'm doing that well.
any ideas would be great
thanks |
Do this instead:
Momentary Swtich -> EG 1 Trig In
EG1 Out -> VCA Control ("Control Input")
Mod. Generator out -> VCA In
VCA Out -> Total
In the "Frequency Modulation" section just below the VCO Mixer, set the MG/T.EXT to 1 and the EG/EXT to 0.
In the Modulation Generator section, set both knobs to their middle position (aka 5, or 'noon').
Play your keyboard. Press the button.
Every time you press the momentary switch, its triggering EG1 which is controlling the amplitude of the VCA which has the LFO as it's input.. so not only do you have the effect you want (vibrato is only on while button is pressed) you can also fine tune the attack/release of it with the EG-1 controls.
Adjust the amount with the FM knob previously mentioned, and the freq. and waveform controls in the modulation generator. _________________ korgs: MS20, MS20 Mini, MS2000, KP1/KP3, Kaossilator, microX, padKontrol, DS-10+, Electribe ESX-1, ER1-MKII, Monotribe+midi
Last edited by plosive on Fri Jul 05, 2013 11:40 am; edited 1 time in total |
|
Back to top |
|
|
plosive Full Member
Joined: 08 Feb 2008 Posts: 248
|
Posted: Fri Jul 05, 2013 11:16 am Post subject: |
|
|
hrmn.. if you do that you lose the ability to use your mod wheel to 'total'.
that is... unless you have a mixer or piggy back cable so you can assign 2 inputs to the total.
like one of these:
http://www.analoguehaven.com/tiptopaudio/stackcable/
(or you could just use the freq mod knob directly instead of patching it to the m.wheel or m.switch) _________________ korgs: MS20, MS20 Mini, MS2000, KP1/KP3, Kaossilator, microX, padKontrol, DS-10+, Electribe ESX-1, ER1-MKII, Monotribe+midi
|
|
Back to top |
|
|
brandon Junior Member
Joined: 20 Sep 2008 Posts: 52
|
Posted: Sat Jul 13, 2013 5:02 pm Post subject: |
|
|
Thanks! |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|