Korg Forums

Hopefully, though, if Korg are close to a new model or even OS update that radically changes the sample slots, they test it more thoroughly than 3.1 for compatibility issues with older sample sets... It does look somewhat likely that the change in memory structure is the cause of some of the ...

Hello

what matters today, since the Pa4x is in the last months of its existence before the release of a new model, it is an update which allows to increase the maximum number of samples supported in order to reach at least the 25,000 samples.

Hello The problem of the Pa4x lies in the quality of the sound card or in the software because by comparing it with the sounds of the pa1000 and the Pa3x (on the same mixer and with the same drumkit and sounds), you can see that the output sounds of the Pa4x is very poor since the update of the V3 ...

Hello the v3 NEXT version of the Korg pa4x must be reviewed before the Pa4x retires. in addition to the problems raised above, it is necessary: -Increase the maximum number of samples to increase to more than 25000 samples in order to allow us to use 1.5Gb of RAM. -Review the sound output quality ...

Hello
I do not understand why Korg does not configure NANOPAD2 to allow us to configure the PAD of korg pa4x?
However, it is the most basic of uses !!!!!

Nowhere do I see what type of PA the OP is using... TBH, if the arranger sounds good in the studio but awful live, it strikes me that the problem lies with the PA. And trying to compensate with Maxx still doesn’t address everything ELSE being put through the PA system. Rather than fix only the a ...

Let's wait till the end of the month, i think an Os's udpate might be close now, (maybe V.3.1.1 ? ) we will check them again then. I hope they will also increase the maximum number of samples supported by the pa4x in order to allow us to use 1.5Gb of Ram. the 21000 (drum & sound) samples are not ...

Could you do a test for us? Can you load some pa1000 factory's sounds on pa4x and test them or compare them to the existing sounds on pa4x? Can you load some pa4x' sounds on pa1000 and test if the result is the same? Hello I have already done the test: 1-I took the sounds of Pa1000 and I put them ...

I guess it's because now the sound is clean of bad frequencies, you can hear now more details,but check what you said about reverb. Is it much overall in factory styles too or just in your custom styles? If there is much,first be sure that your cables are balanced and signal is ok, then if still ...

Possibility of opening the lock function of the Pa4x screen with password in order to protect our keyboards during outdoor use. this function is very useful and Yamaha has already integrated it at the Genos level. I support both of your wish lists regarding increasing number of samples and password ...

Hello is there a software update on Pa4x which will increase the maximum number of samples (sound & drums) in order to benefit from 1,5Gb of Ram? Why not increase the number of samples by PCM up to 256 samples, in order to allow Pa4x to reach (256 * 99) = 25,344 samples instead of 21,000 samples ...

i was happily surprised when i saw a clip recorded using an i-phone,and the sound was clear. Then i first realized that my settings were ok. So,according to my custom styles i use,factory styles as well , best working settings for MAXX is like this: EQ: IN=BELL OUT=BELL GAIN: 0.3 | 1.1 |-3.1 | 00 ...

my thanks for the precious explanations. indeed, since the release of the Next version on the pa4x, I think that the sound quality on the pa4x has been modified compared to the V2 version. moreover, i have the impression that the pa1000 sounds better than the pa4x by importing the same program from ...

DELLRACHIDO if the sound is overall ballanced, the only adjustment you will need to make is your volume, and the most extreme adjustment is the BASS value, just try it , even if it doesn't sound that good in first , compared to other presets you might have. the problem is that i have two types of ...

i was happily surprised when i saw a clip recorded using an i-phone,and the sound was clear. Then i first realized that my settings were ok. So,according to my custom styles i use,factory styles as well , best working settings for MAXX is like this: EQ: IN=BELL OUT=BELL GAIN: 0.3 | 1.1 |-3.1 | 00 ...