Korg Forums

Hi Timo

Did you get the file?

Regards

ProfPlat

Thanks to samriccijr for scanning in the sysex text. I have adobe writer and have combined this and the original manual. Can I email it to someone so they can update the sticky for the Trinity Parameter Guide?

I have MQ on a really old separate PC (Pentium 3, 256 RAM 497 MHz XP (upgrade from W98!!) and no antivirus as that kills the PC!) and run it stand alone ( I have just checked dates and the PC is 15 years old to the day!). I have had probs with other MQ editors, but this one was asking for the right ...

Ok here we go. I have done both (forgive the cut and paste, imagine a tab between the value and F0: Value Start Level 99 F0 42 30 3B 41 03 00 06 00 00 00 63 F7 98 F0 42 30 3B 41 03 00 06 00 00 00 62 F7 60 F0 42 30 3B 41 03 00 06 00 00 00 3C F7 2 F0 42 30 3B 41 03 00 06 00 00 00 02 F7 1 F0 42 30 3B ...

Am at work at the moment. Will have a look tonight. As you have probably seen from my previous posts, the MQ editor is just not thoroughly checked when made. For instance, for a patch, you can change it between a single, double or drum. The code behind this parameter is wrong, a simple tweak and all ...

If you let me know what parameter you want to change (let us just do 1 to keep things simple at this stage) I will get MQ 10 to change it, record the output and then post it here. This will give us the MSB and LSB. The only difficult parameters (to calc the MSB/LSB) will be the ones that go from -99 ...

Does the BCR2000 output sysex or CC messages?

You will only use the parameter table if the BCR2000 uses sysex (which I don't think it does).

However you can use CC messages to change parameters using Alternate Modulation see Trinity Parameter guide appendix 8 for starters.

I looked at the manual for the BCR2000, and it looks like it only uses CC messages, so you only need to use the Control messages : Bn xx vv. Where n is the channel (0-F), xx is the CC no (from the midi messages chart) and vv is the value 00 – 7F. Eg B0 4A 7F sets the brightness for channel 1 to max. ...

Ah, this maybe your problem. The multi mode on the TR-Rack is not like anything else. Parameters cannot be changed using sysex (only a complete dump is allowed - This is from MQ as well as the sysex chart). There is only 1 multi, so you cannot save different setups, ie there is no bank of multis ...

The guts of the TR-Rack are the same as the Trinity. The front panel editing does not directly reflect the individual parameters that you can change on the Trinity, eg you cannot change the type of wave for a patch from the front panel, it can only be changed using software. Anything you change in ...

Just reset TR rack, I searched the internet to find the hold edit and A4 when switching on (rather than read the manual) and came across: Check ROM: Hold "Edit" and ">" while powering on, o.s 1.0.4. Could not find any notes about it. Tried it, pushed some buttons. Anybody know a bit more about it ...

Hi skyler Now I have the sysex for the TR-Rack I will be spending time going into the midiquest 10 editor and checking the code. Did you get the error doing anything in particular: Combi, program, parameter change etc. I use midi cables to connect to my old XP PC, which has a cheap PCI sound card ...

Just been over to the Korg website and under drivers?? for the trinity they have a spreadsheet with the effects parameter nos. I will check these out.

ProfPlat

Sam
Thank you - just what I was looking for.

ProfPlat

You are a star - Thank you