can't change tracks in sequence

kawwi8 · Post by **kawwi8** » Sat Jun 13, 2009 4:38 pm

many times when I'm working on my triton in sequencer I can't change tracks ,I have to save the project then power off the keyboard and power on it again to countinue my work..I don't attach any external device expect the Compact flash 1GB...

jerrythek · Post by **jerrythek** » Sat Jun 13, 2009 5:34 pm

If you are holding a key on the keyboard, or moving the joystick etc. you can't change tracks. That may be your problem...

Regards,

jerry

kawwi8 · Post by **kawwi8** » Sat Jun 13, 2009 6:20 pm

thank you for your reply...
no I'm sure I'm not holding any key or etc...do you think this issu be a hardware problem?..because when I restart triton the problem will fixed..
I upgraded to last firmware 1.0.6 and restore to original setting and same problem remain..

Post by **Sharp** » Sat Jun 13, 2009 7:04 pm

I don't attach any external device expect the Compact flash 1GB...

Assuming you REALLY mean that and you don't even have so much as a pedal connected, go to GLOBAL mode and make sure the damper polarity is set to KORG. Don't forget to save the changes.

Regards
Sharp,

kawwi8 · Post by **kawwi8** » Sat Jun 13, 2009 9:44 pm

Thank you very much this solution may fix my problem ,but let me try working on my keyboard to test it because as I mention this issue accrue from time to time not every time...
thanks again

Regards
Kawan

kawwi8 · Post by **kawwi8** » Sat Jun 13, 2009 9:51 pm

and sorry for my bad English...in my first post I wrote (expect compact flash 1gb)..

i mean (Except compact flash 1GB)..

bugg1 · Post by **bugg1** » Thu Jun 18, 2009 4:16 pm

I have the exact same problem. I do have 2 pedals connected to the TE. A square yellow/black Korg pedal into the switch connection and a Yamaha Damper pedal in the damper connection.

I can switch tracks no problem for a while, then after the keyboard has been on for 1 -2 hours I can't switch from one track to another.

A related problem, I also can't play the keyboard while the sequence is running, stop the sequence, and continue to play the sound I was playing. When you stop the sequencer all sounds cut off very abruptly. The Triton ProX I had didn't have a problem letting you continue to play after stopping the sequence.

Any help will be great. Thanks.

Post by **Sharp** » Thu Jun 18, 2009 5:07 pm

Hi bugg1.

The Yamaha pedal is extremely likely to be the cause of your problems.
You really should only use a KORG one and flip the polarity in Global mode back the way it should be.

Another fix I've heard of is people cutting the jack off Yamaha cables and rewiring them up the same as KORG ones.

Regards.
Sharp.

bugg1 · Post by **bugg1** » Thu Jun 18, 2009 5:45 pm

Sharp wrote:Hi bugg1.

The Yamaha pedal is extremely likely to be the cause of your problems.
You really should only use a KORG one and flip the polarity in Global mode back the way it should be.
Another fix I've heard of is people cutting the jack off Yamaha cables and rewiring them up the same as KORG ones.

Regards.
Sharp.

That might be the problem. If I unplug the pedals, turn on the TE, and try to stop the sequencer with the buttons, it does the same thing.

I will try that and if it works will buy a Korg DS1H to use. I'll let you know one way or the other.

Thanks!!!

Post by **Sharp** » Thu Jun 18, 2009 5:50 pm

If I unplug the pedals, turn on the TE, and try to stop the sequencer with the buttons, it does the same thing.

Just follow my instructions and it will not happen.
You are not flipping the polarity back to KORG as I said.

Kind Regards.
Sharp.

bugg1 · Post by **bugg1** » Thu Jun 18, 2009 6:04 pm

Cool.

I will try that when I get home from work today. That will make the shows go so much better!!!!

Can't wait!!!

Thanks again!

bugg1 · Post by **bugg1** » Thu Jun 18, 2009 9:46 pm

OK I tried exactly what you said and ........

same result. Stop sequence and ALL sounds cut off aburptly.
Anything else I can try?

jg:: · Post by **jg::** » Fri Jun 19, 2009 9:27 am

This issue sometimes happens if you are holding down a key or using the joystick or pedal at the time you stop recording. In other words, if things have not been re-set to zero, or centre, or all notes off at the time you press the stop button.

Be careful to restore everything to "zero" before ending recording, and see if that helps.

jg::

bugg1 · Post by **bugg1** » Fri Jun 19, 2009 5:42 pm

I should have been more clear.

Actually it is when I am playing along with a sequence I have already recorded.

Example :

I am playing along with the sequence and the band is ready to end the song, to hold the ending I have to hit the pause button. I can't hit stop or use the pedal to stop the sequence. If I do then everything cuts off.

jg:: · Post by **jg::** » Sat Jun 20, 2009 9:16 am

I was responding to the issue at the top of this thread. For your second problem, perhaps you should start another thread... :-]

jg::