Hello,
I have 2 question, so if someone can help me regatding Trinity Pro it would be great.
1. I have played a little with software and put 3.1 or 3.12 and back again
2.41 and I have lost my S bank!!!! Why???!!
How can I get it back?
I tryed to initialize but only gives me A, B, C and D bank cause I have
TRI PBS option.
2. Does anyone have original brochure or catalog fro Korg Trinity?
There is a flight case from Korg in silver color and there was a
picture and products number-
I'm lookin cause I want to buy it or make a replica-
2 questions
Moderators: Sharp, X-Trade, Pepperpotty, karmathanever
2 questions
Korg Kronos 2 73, Korg Triton Extreme 61, Korg Trinity, Roland D-50, Yamaha DX7 IIFD, Korg T2EX
-
korg_nikos
- Full Member
- Posts: 241
- Joined: Sun Jun 11, 2006 4:35 pm
- Location: Athens Greece
First of all: Why did you load Version 3.1.x? This is only for Trinity V3 (Pro) or (ProX) which feature Moss-Tri (Bank M) instead of Solo-Tri (Bank S). Version 3.1.x causes the instrument to ignore Solo-Tri because it expects to find a Moss-Tri connected on the main board. If not it will not recognize Solo-Tri. You will have to reload a fresh copy of 2.41 in order to recognize Solo-Tri again.
If you have done it already and still does not find the Solo-Tri try the following.
1. Open the back cover (Remove all screws apart from those two that hold the base for the keybed.
2. Locate the Solo-Tri board.
3. Disconect it from mainboard.
4. Put the cover back on (Use 2 or 3 screws only cuz you will need to open the cover again)
5. Hold Enter+0 while turning the instrument on. Banks A,B,C and D will be initialized.
6. Turn the instrument off.
7. Hold Enter + Reset while turning the instrument on and load 2.41 Version (Download fresh copy from Korg using 2 new floppies).
8. Turn the instrument off and remove back cover.
9. Reconnect Solo-Tri to the mainboard.
10. Put the cover back and turn on the instrument. Your S bank should be there but initialized.
Again if after those 10 steps your instrument does not find Solo-Tri and S bank there is something wrong with
i) Solo-Tri
ii) Mainboard
iii) Connectors
iv) Bad Copy of OS Version or Bad Sector on Floppy 1 or 2 containing OS data.
Be careful not to turn the instrument off while OS loading. If so your instrument will have to be returned to Korg.
If you have done it already and still does not find the Solo-Tri try the following.
1. Open the back cover (Remove all screws apart from those two that hold the base for the keybed.
2. Locate the Solo-Tri board.
3. Disconect it from mainboard.
4. Put the cover back on (Use 2 or 3 screws only cuz you will need to open the cover again)
5. Hold Enter+0 while turning the instrument on. Banks A,B,C and D will be initialized.
6. Turn the instrument off.
7. Hold Enter + Reset while turning the instrument on and load 2.41 Version (Download fresh copy from Korg using 2 new floppies).
8. Turn the instrument off and remove back cover.
9. Reconnect Solo-Tri to the mainboard.
10. Put the cover back and turn on the instrument. Your S bank should be there but initialized.
Again if after those 10 steps your instrument does not find Solo-Tri and S bank there is something wrong with
i) Solo-Tri
ii) Mainboard
iii) Connectors
iv) Bad Copy of OS Version or Bad Sector on Floppy 1 or 2 containing OS data.
Be careful not to turn the instrument off while OS loading. If so your instrument will have to be returned to Korg.