Holding shift While adjusting wave shape question

Discussion relating to the Korg Prologue

Moderators: Sharp, X-Trade, Pepperpotty, karmathanever

Post Reply
cornguy
Posts: 11
Joined: Fri May 29, 2020 12:21 pm

Holding shift While adjusting wave shape question

Post by cornguy »

Hi, just joined the world of synthesizers and I'm loving it. Been slowely figuring things out, today, what I am curious about, is what exactly holding shift down while adjusting the 3rd oscillator will do. I don't think it's meant to do anything for osc 1 and 2, but If I believe the instructions said you can use it to further change the shape of the wave. But when i do it, nothing seems to happen. Is this a user error or could maybe something else be wrong? thanks :)
Narioso
Senior Member
Posts: 300
Joined: Thu Oct 15, 2015 9:18 am
Location: Sweden

Post by Narioso »

For each user oscillator of the 16 allowed it can be anything - you have to look at specs for those. Those are coded individually. Some don't use that at all. Some does not make a beep even without some action in menus.

For VPM type I think manual says some things what it does, with shift modulator ratio where without shift it does modulator depth.

But overall it's only for multi engine(osc 3).

But recall as you said, on osc 1 and 2 shift shape does nothing - to my surprise. Maybe a firmware update will introduce something there, one never knows.
MIDI gear: Sequential REV2.16, Prologue-8, Hammond XK-3C, Kawai MP7SE piano, Nord Lead 2X, Roland D-05
cornguy
Posts: 11
Joined: Fri May 29, 2020 12:21 pm

Post by cornguy »

Ok thanks :) so its only for the user added oscillators and not for the ones included such as sin1 etc?
Narioso
Senior Member
Posts: 300
Joined: Thu Oct 15, 2015 9:18 am
Location: Sweden

Post by Narioso »

It's for VPM as well, the ratio I mentioned, that is in manual.
MIDI gear: Sequential REV2.16, Prologue-8, Hammond XK-3C, Kawai MP7SE piano, Nord Lead 2X, Roland D-05
cornguy
Posts: 11
Joined: Fri May 29, 2020 12:21 pm

Post by cornguy »

OK i think I get it now, thanks :)
MRNUTTY
Posts: 41
Joined: Mon Oct 03, 2011 8:37 pm

Post by MRNUTTY »

As of 2.10 -
Shift is used for:
Shift-Tuning - When the prologue's sound generator is not making any sound, auto-tuning occurs au-tomatically; but you can use this function to retune the prologue manually in Play mode if the tuning seems to be drifting. The internal temperature tends to changes more right after the power is turned on, which may cause the instrument to go out of tune. Press the EXIT button while holding down the SHIFT button again to cancel manual tuning, if you accidentally started it by mis-take.

Shift-Pitch (VCO's only) - set pitch in semitones.

Shift-Effect select - OFF/ON/SELECT switch (MOD EFFECT), Pushing this switch to SELECT allows you to set the effect's sub-type.

LFO waveform phase settings - INT knob (LFO) - This allows you to invert the phase of the LFO waveform.

MULTI ENGINE parameter settings - SHAPE knob - (MULTI ENGINE) - Adjusts the modulator ratio when setting the VPM with the MULTI ENGINE's NOISE/ VPM/USR switch. Or defined by User Oscillator when USR is selected.
cornguy
Posts: 11
Joined: Fri May 29, 2020 12:21 pm

Post by cornguy »

thanks :)
Post Reply

Return to “Korg Prologue”