Portamento (glide) on Polysix program

Discussion relating to the Korg Kronos Workstation.

Moderators: Sharp, X-Trade, Pepperpotty, karmathanever

aellison62
Full Member
Posts: 160
Joined: Tue May 11, 2010 12:05 pm

Portamento (glide) on Polysix program

Post by aellison62 »

Ok, where exactly is the portamento parameter on a Polysix program?? Is it me or is it somewhere not very intuitive? 🤨
Current gear: Kurzweil Forte 7, Kurzweil PC361, Mojo 61, Korg Kronos X 61, Roland RD-88, Korg Nautilus 73
aellison62
Full Member
Posts: 160
Joined: Tue May 11, 2010 12:05 pm

Post by aellison62 »

Never mind, I see that Polysix doesn’t support portamento.
Current gear: Kurzweil Forte 7, Kurzweil PC361, Mojo 61, Korg Kronos X 61, Roland RD-88, Korg Nautilus 73
User avatar
ronnfigg
Platinum Member
Posts: 2161
Joined: Sat Mar 26, 2011 4:56 am
Location: CA

Post by ronnfigg »

The original didn't have it either. I had one. The MonoPoly had it.
"To me the synthesizer was always a source of new sounds that musicians could use to expand the range of possibilities for making music."
Bob Moog
psionic311
Platinum Member
Posts: 1046
Joined: Fri Nov 14, 2014 11:57 am
Location: Orlando, Florida USA

Post by psionic311 »

Just for kicks, I thought I'd see if the Kronos could override those defaults. Unfortunately it can't.

You can go to COMBI mode and select the Timbre/OSC tab to override the Portamento settings on the individual program. But it only works for engines that can do portamento already.... the Poly6EX still ignores glide.
19naia
Platinum Member
Posts: 1217
Joined: Thu Nov 29, 2012 7:05 pm

Post by 19naia »

Is there a way to route the polysix audio into a program that has portamento and then get the portamento to work on the audio input?

I know EXi audio input can happen in several synth engines, and can route audio in via FX control 1 & 2, IFX, indv. pairs, inputs 1&2 plus USB and SPDIF.

That definitely makes it possible to route PlolySix into one of the other synth engines.

The question is wether doing that will allow Portamento from one of the engines to effect Polysix audio.
User avatar
ronnfigg
Platinum Member
Posts: 2161
Joined: Sat Mar 26, 2011 4:56 am
Location: CA

Post by ronnfigg »

I think the real question here is why didn't Korg build portamento into the PolySix EX engine? Last time I checked the original MS-20 was monophonic, yet the MS-20EX can be polyphonic.
"To me the synthesizer was always a source of new sounds that musicians could use to expand the range of possibilities for making music."
Bob Moog
CharlesFerraro
Platinum Member
Posts: 955
Joined: Sat Feb 06, 2010 10:15 am
Location: California

Post by CharlesFerraro »

19naia wrote:Is there a way to route the polysix audio into a program that has portamento and then get the portamento to work on the audio input?
That won't work. We can discuss why but I don't want to launch into an overly wordy explanation.

The only way to get portamento out of the Polysix would be to use KARMA's auto pitch bend feature. Even then I haven't tried to see if it could deliver a convincing portamento. And if it could I'm fairly certain it would be monophonic. Not the timbre, that'd still be poly unless specified otherwise, but rather the bend calculation would be mono or perhaps get confused by chords. Therefore it'd be best to set the Polysix to mono. Also I don't think each portamento bend calculation would work past an octave away from the previously pressed note.

It's something worth trying if you absolutely need portamento on the Polysix.
paypal.me/CharlesFerraro
PCFREE
Platinum Member
Posts: 528
Joined: Sun Sep 02, 2012 10:54 pm
Location: Just passing through...

Post by PCFREE »

One tedious workaround would be to resample the program and then apply portamento in HD1
Korg Nautilus 61 AT, Kurzweil Forte 7
....as we forgive those who synthesize against us!!
CharlesFerraro
Platinum Member
Posts: 955
Joined: Sat Feb 06, 2010 10:15 am
Location: California

Post by CharlesFerraro »

PCFREE wrote:One tedious workaround would be to resample the program and then apply portamento in HD1
What an excellent suggestion! Why didn't I think of that :idea:
paypal.me/CharlesFerraro
Liviou2004
Platinum Member
Posts: 1150
Joined: Mon Feb 20, 2017 11:28 am
Location: France

Post by Liviou2004 »

aellison62 wrote:Ok, where exactly is the portamento parameter on a Polysix program?? Is it me or is it somewhere not very intuitive? 🤨
As it has been said, there were no Portamento on original Polysix, and nor in PolysixEx.

Some months ago, I've found a method, using Combination :

1°) Prog Mode
A) Take an Init Prog. AL-1 Engine. In Mixer Tab, all volumes at 0, except Sub Osc/Audio. Set Audio Input to Input 1. The purpose of this Program is only to receive another Program audio signal though the Audio Input. So, it won't produce any sound by itself.
B) Locate your Polysix Program on which you want to apply a portamento

2°) Combi Mode.
Take an Init Combi. Place the former AL-1 Prog on Track 1. It will be the "receiver Track", so to speak.

3°)Track 2, place your Polysix Prog. It will be the transmitter Prog, so to speak.

4°) P8 : Insert Effect, Routing 1Tab, Track 2 Bus Select on “1” (Individual output 1). The timbre will be sent in mono to the Individual output 1.

5°) Plug a jack in Audio Individual ouput 1 and in Audio Input 1. In this way, the Polysix audio sound is sent in Audio Input 1, toward the AL-1 Exi Audio Input. So, your Polysix Prog will use the AL-1 settings. you can set the Portamento as you want in AL-1 settings. Your Polysix prog is using all the AL-1 settings, including Portamento.

I hope it will be clear enough.
CharlesFerraro
Platinum Member
Posts: 955
Joined: Sat Feb 06, 2010 10:15 am
Location: California

Post by CharlesFerraro »

Liviou2004 wrote:As it has been said, there were no Portamento on original Polysix, and nor in PolysixEx.

Some months ago, I've found a method, using Combination :

1°) Prog Mode
A) Take an Init Prog. AL-1 Engine. In Mixer Tab, all volumes at 0, except Sub Osc/Audio. Set Audio Input to Input 1. The purpose of this Program is only to receive another Program audio signal though the Audio Input. So, it won't produce any sound by itself.
B) Locate your Polysix Program on which you want to apply a portamento

2°) Combi Mode.
Take an Init Combi. Place the former AL-1 Prog on Track 1. It will be the "receiver Track", so to speak.

3°)Track 2, place your Polysix Prog. It will be the transmitter Prog, so to speak.

4°) P8 : Insert Effect, Routing 1Tab, Track 2 Bus Select on “1” (Individual output 1). The timbre will be sent in mono to the Individual output 1.

5°) Plug a jack in Audio Individual ouput 1 and in Audio Input 1. In this way, the Polysix audio sound is sent in Audio Input 1, toward the AL-1 Exi Audio Input. So, your Polysix Prog will use the AL-1 settings. you can set the Portamento as you want in AL-1 settings. Your Polysix prog is using all the AL-1 settings, including Portamento.

I hope it will be clear enough.
Can confirm that does not work. Strange because that's the second suggestion to try routing into another synth engine. There's no way to take an audio input as is and apply a portamento effect. Think of it like this, would it be possible to take a person's voice and apply portamento in real time? Nope! It's no different from routing a synth oscillator to an input so you shouldn't expect otherwise. I'd urge you to double check your previous experiment.

Btw, I didn't realize AL-1 carries vestigial inputs from the OASYS. Audio inputs 1/2 work, as well as s/pdif. But the Kronos doesn't have the second pair of stereo inputs 3/4. Would be pretty sweet if it did. There's no way to route to the analog inputs digitally from within the keyboard. Therefore it's not possible to route internally to AL-1 at all. Those were some good learning points that came out of this for me.

There are other synth engines you can route to internally such as the MS-20 or MOD-7 etc. As mentioned, their portamento settings would have no direct effect whatsoever to whatever audio input you feed into them.
paypal.me/CharlesFerraro
User avatar
ronnfigg
Platinum Member
Posts: 2161
Joined: Sat Mar 26, 2011 4:56 am
Location: CA

Post by ronnfigg »

Thanks Charles.
"To me the synthesizer was always a source of new sounds that musicians could use to expand the range of possibilities for making music."
Bob Moog
Lightbringer
Senior Member
Posts: 356
Joined: Sun Jan 07, 2018 11:16 pm
Location: USA

Post by Lightbringer »

PCFREE wrote:One tedious workaround would be to resample the program and then apply portamento in HD1
This is turning into an interesting thread.

My initial thought is "that does sound tedious."

My second thought is that it's probably not all that tedious, if internal resampling was something I'd done much of, and really had a process flow down for.

Anyone have thoughts on the best approach for resampling an internal synth? Would it be to record a sequence of each individual note in SEQ, then use time slicing to split them up? Record each note individually? Split them into ranges of a half octave or so and sample only the bottom note?
Liviou2004
Platinum Member
Posts: 1150
Joined: Mon Feb 20, 2017 11:28 am
Location: France

Post by Liviou2004 »

CharlesFerraro wrote:
Liviou2004 wrote:As it has been said, there were no Portamento on original Polysix, and nor in PolysixEx.

Some months ago, I've found a method, using Combination :

1°) Prog Mode
A) Take an Init Prog. AL-1 Engine. In Mixer Tab, all volumes at 0, except Sub Osc/Audio. Set Audio Input to Input 1. The purpose of this Program is only to receive another Program audio signal though the Audio Input. So, it won't produce any sound by itself.
B) Locate your Polysix Program on which you want to apply a portamento

2°) Combi Mode.
Take an Init Combi. Place the former AL-1 Prog on Track 1. It will be the "receiver Track", so to speak.

3°)Track 2, place your Polysix Prog. It will be the transmitter Prog, so to speak.

4°) P8 : Insert Effect, Routing 1Tab, Track 2 Bus Select on “1” (Individual output 1). The timbre will be sent in mono to the Individual output 1.

5°) Plug a jack in Audio Individual ouput 1 and in Audio Input 1. In this way, the Polysix audio sound is sent in Audio Input 1, toward the AL-1 Exi Audio Input. So, your Polysix Prog will use the AL-1 settings. you can set the Portamento as you want in AL-1 settings. Your Polysix prog is using all the AL-1 settings, including Portamento.

I hope it will be clear enough.
Can confirm that does not work. Strange because that's the second suggestion to try routing into another synth engine. There's no way to take an audio input as is and apply a portamento effect. Think of it like this, would it be possible to take a person's voice and apply portamento in real time? Nope! It's no different from routing a synth oscillator to an input so you shouldn't expect otherwise. I'd urge you to double check your previous experiment.

Btw, I didn't realize AL-1 carries vestigial inputs from the OASYS. Audio inputs 1/2 work, as well as s/pdif. But the Kronos doesn't have the second pair of stereo inputs 3/4. Would be pretty sweet if it did. There's no way to route to the analog inputs digitally from within the keyboard. Therefore it's not possible to route internally to AL-1 at all. Those were some good learning points that came out of this for me.

There are other synth engines you can route to internally such as the MS-20 or MOD-7 etc. As mentioned, their portamento settings would have no direct effect whatsoever to whatever audio input you feed into them.
I don't fully agree with you. I agree because portamento doesn't work with my method.
But, we can apply all other settings (filter, resonance, enveloppe, ,etc) to the initial Polysix signal. I just tried and it works. It can be interesting to get the Polysix signal into AL-1 filters, if we want. We can do many others operations, too.
Indeed, portamento isn't applied. But, as the first audio signal is digitalized, there is no theoretical obstacle to do that. But, you're right : the fact is that it doesn't work !
Yes, I knew it is not possible to route internally an audio signal into the AL-1. That's the reason why I was looking for another way to do that. I knew it was working, but never tried with Portamento setting.
(Three other Exi can do that : MOD-7, STR-1 and MS-20).
User avatar
ronnfigg
Platinum Member
Posts: 2161
Joined: Sat Mar 26, 2011 4:56 am
Location: CA

Post by ronnfigg »

Liviou2004 wrote:
CharlesFerraro wrote:
Liviou2004 wrote:As it has been said, there were no Portamento on original Polysix, and nor in PolysixEx.

Some months ago, I've found a method, using Combination :

1°) Prog Mode
A) Take an Init Prog. AL-1 Engine. In Mixer Tab, all volumes at 0, except Sub Osc/Audio. Set Audio Input to Input 1. The purpose of this Program is only to receive another Program audio signal though the Audio Input. So, it won't produce any sound by itself.
B) Locate your Polysix Program on which you want to apply a portamento

2°) Combi Mode.
Take an Init Combi. Place the former AL-1 Prog on Track 1. It will be the "receiver Track", so to speak.

3°)Track 2, place your Polysix Prog. It will be the transmitter Prog, so to speak.

4°) P8 : Insert Effect, Routing 1Tab, Track 2 Bus Select on “1” (Individual output 1). The timbre will be sent in mono to the Individual output 1.

5°) Plug a jack in Audio Individual ouput 1 and in Audio Input 1. In this way, the Polysix audio sound is sent in Audio Input 1, toward the AL-1 Exi Audio Input. So, your Polysix Prog will use the AL-1 settings. you can set the Portamento as you want in AL-1 settings. Your Polysix prog is using all the AL-1 settings, including Portamento.

I hope it will be clear enough.
Can confirm that does not work. Strange because that's the second suggestion to try routing into another synth engine. There's no way to take an audio input as is and apply a portamento effect. Think of it like this, would it be possible to take a person's voice and apply portamento in real time? Nope! It's no different from routing a synth oscillator to an input so you shouldn't expect otherwise. I'd urge you to double check your previous experiment.

Btw, I didn't realize AL-1 carries vestigial inputs from the OASYS. Audio inputs 1/2 work, as well as s/pdif. But the Kronos doesn't have the second pair of stereo inputs 3/4. Would be pretty sweet if it did. There's no way to route to the analog inputs digitally from within the keyboard. Therefore it's not possible to route internally to AL-1 at all. Those were some good learning points that came out of this for me.

There are other synth engines you can route to internally such as the MS-20 or MOD-7 etc. As mentioned, their portamento settings would have no direct effect whatsoever to whatever audio input you feed into them.
I don't fully agree with you. I agree because portamento doesn't work with my method.
But, we can apply all other settings (filter, resonance, enveloppe, ,etc) to the initial Polysix signal. I just tried and it works. It can be interesting to get the Polysix signal into AL-1 filters, if we want. We can do many others operations, too.
Indeed, portamento isn't applied. But, as the first audio signal is digitalized, there is no theoretical obstacle to do that. But, you're right : the fact is that it doesn't work !
Yes, I knew it is not possible to route internally an audio signal into the AL-1. That's the reason why I was looking for another way to do that. I knew it was working, but never tried with Portamento setting.
(Three other Exi can do that : MOD-7, STR-1 and MS-20).
This thread originally started out as a question about portamento on a Korg PolySix. The original poster then followed up and realized that portamento was not supported on the Korg PolySix. End of story. Yes you can plug it into other synth and use all the parameters you mentioned, but portamento is not achievable. So what was the point of cluttering up this thread. Might have been better to start a new thread. That would be a major help for people whose search the threads for specific topics. Having to wade through a thread like this to find out what they are looking for is not available could be a real pain in the butt. Not trying to be a jerk here, just trying to make these forms a little bit easier to use for everyone. I will admit that I even went off topic a little bit. Please accept my apologies.
Last edited by ronnfigg on Wed Feb 20, 2019 6:46 am, edited 1 time in total.
"To me the synthesizer was always a source of new sounds that musicians could use to expand the range of possibilities for making music."
Bob Moog
Post Reply

Return to “Korg Kronos”