Hi All
I just baught a yamaha psrs910, and I would like to midi just the tc helcon to the yamaha, how would I do this? the pa 800 has in my opinion a great harmonizer. the 910 is also nice but the pa800 is the best. thanks,
Paula
midi
Moderators: Sharp, X-Trade, Pepperpotty, karmathanever
-
LESSISMORE
- Platinum Member
- Posts: 531
- Joined: Wed Jul 15, 2009 8:37 pm
- Location: Germany
Hi Paula
Please try this :
You need a mic-line from your mixer to the PA800-Mic-In. (Aux-Out, Monitor-Out...) Or go direct with your mic into the PA800.
Then connect a Midi-Cable from your S910-out to PA800-In.
Now sing in your mic and play on your S910.
With a little bit luck, it will work without making settings.
The factory-settings on the arranger-keys is normally to send on channal 4 with the lower-part. (left hand in style-mode)
When there is a problem, please checkout the midi-settings of both keys.
Or ask another time.
Good luck.
Please try this :
You need a mic-line from your mixer to the PA800-Mic-In. (Aux-Out, Monitor-Out...) Or go direct with your mic into the PA800.
Then connect a Midi-Cable from your S910-out to PA800-In.
Now sing in your mic and play on your S910.
With a little bit luck, it will work without making settings.
The factory-settings on the arranger-keys is normally to send on channal 4 with the lower-part. (left hand in style-mode)
When there is a problem, please checkout the midi-settings of both keys.
Or ask another time.
Good luck.
thanks
HI LESS,
thank you for the quick response, I don't use a mixer, just powered speakers. I did finally get it to work after 1000000000 of hours BUT, turned the key boards on all gone, I did write midi globel set up to the korg, the yamaha well what can I say, well you know there are so many settings on both k.b I put the wires this way.. midi in korg ..korg master k.b.. yamaha wire out and seems to be a million menu's on yamaha I set lower part to ch 4 and transmit,works untill I shut down, oh I can't explane it all in writing IT's crazy, I guess I just have to work it out, thanks any way.
I watch you on you tube your music is great, especially the Mr. sand man song.
Paula
thank you for the quick response, I don't use a mixer, just powered speakers. I did finally get it to work after 1000000000 of hours BUT, turned the key boards on all gone, I did write midi globel set up to the korg, the yamaha well what can I say, well you know there are so many settings on both k.b I put the wires this way.. midi in korg ..korg master k.b.. yamaha wire out and seems to be a million menu's on yamaha I set lower part to ch 4 and transmit,works untill I shut down, oh I can't explane it all in writing IT's crazy, I guess I just have to work it out, thanks any way.
I watch you on you tube your music is great, especially the Mr. sand man song.
Paula
-
LESSISMORE
- Platinum Member
- Posts: 531
- Joined: Wed Jul 15, 2009 8:37 pm
- Location: Germany
midi
HI LESS, your right, another question to you how does it work I have my pa800 set to follow the cords, so being the korg is the master , just by putting midi wire to 910and not telling it what to do it seems to work ? all the grief this has given, now I think all I needed to do was play one cord on the pa800 just to get it started, thankyou so very much.
Paula
Paula
-
LESSISMORE
- Platinum Member
- Posts: 531
- Joined: Wed Jul 15, 2009 8:37 pm
- Location: Germany
Hi Paula
yes that will work also.
You have to look for the Midi-Out Setup of your PA800.
There you can switch on and off each channal.
On the Midi-Filter-side you can filter out "program-Changes and other.
So you can setup both Keys, so they will work fine .
Both keys may be a master. Use both midi-connections. (Use Midi-Filters !!!)
yes that will work also.
You have to look for the Midi-Out Setup of your PA800.
There you can switch on and off each channal.
On the Midi-Filter-side you can filter out "program-Changes and other.
So you can setup both Keys, so they will work fine .
Both keys may be a master. Use both midi-connections. (Use Midi-Filters !!!)